Jump to content
SAU Community

Recommended Posts

Hi all,

When i get my car back next month i will be pulling the turbo off and will be sold,along with braided oil and water lines.

I purchased an 0P6 housing and had it matched with my turbo.Then it was highflowed at Precision Turbos.

Highflow consists of machined front and rear housings(maximum)

Garrett Ball bearing cartridge.(will try and find the serial number for the cartridge)

It also comes with braided oil and water lines.

It has only been on the car for roughly 7000kms and is basically brand new.

I made 250.9rwkw at 16psi with this turbo.Has alot more in it and wouldnt be suprised if it would make 270-280 with a bit more boost.

The rear housing cost me $350

Braided lines $200

Highflowing of turbo $1550

Im asking $1650+post firm.

Old turbo off new turbo on.... big power!

NOW WITH FREE SILICONE INLET PIPE(second hand in excellent condition)

Bass Junky type.

Contact by PM.

CHEERS

post-32255-1197418639_thumb.jpg

post-32255-1197418705_thumb.jpg

post-32255-1197418769_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/197284-highflowed-rb25vg30-bb-turbo/
Share on other sites

  • 1 month later...

OK everyone i have finally got my car back so the turbo will be coming off the car.Those who sent me PMs for the turbo please get in contact with me before it goes to someone else.

dyno chart?

comes with reciepts/warranty?

direct bolt on for r33 gtst s1?

reason for selling?

Doesnt come with a warranty.But the thing is in great condition,i wouldnt be selling it if it wasnt.

Reason for selling is i have another turbo waiting to go in.And it will bolt on no probs comes with braided lines as described in first post.

is the just a standard r33 highflow? fitted it yet?

Sure is mate. Would have loved to buy NYTSKY's turbo its a very well spec'd hiflow but mine was too much of a good deal to pass up.

Its getting tuned today, I'll post up the results tonight after I've taken it for a drive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...