Jump to content
SAU Community

What Events Does Sau Vic Have In The Next Few Months For A Less Experienced Driver?


Recommended Posts

two decent bolts should be sufficient. i have 4 in each extinguisher. i would not be a fan of just 1 bolt. and just to be sure, you are using nuts and bolts, not screws? lots of people screw them in and get knocked back.

4 bolts? Where? Why? :huh:

Anyway, I'm not a fan of 1 bolt but its a street car that *rarely* sees the track (due to $$$), I'm using the rear footwell so one bolt, no nut!

The rear seats have a bolt at the bottom on each side that secures the rear seats in, I've got the Fire Extinguisher with 1 bolt (well its now an allen-key like bolt) going through the extinguisher then securing the rear seat.

I am just using one bolt in mine, with an oversized washer.

The bolt that is used to hold in the rear seat, in the footwell.

Same here, only question is have you done AASA / CAMS events with it before? Just been paranoid, last thing I want is to get knocked back after driving to Shepparton.

You won't get knocked back at DECA. I dare say 99% of people that have them mounted in the rear footwell are only using the 1 botl (Just as I do, and I've done plenty of DECA's)

You won't get knocked back at DECA. I dare say 99% of people that have them mounted in the rear footwell are only using the 1 botl (Just as I do, and I've done plenty of DECA's)

But now they will proably notice, and check :thumbsup:

4 bolts? Where? Why? :thumbsup:

Anyway, I'm not a fan of 1 bolt but its a street car that *rarely* sees the track (due to $$$), I'm using the rear footwell so one bolt, no nut!

The rear seats have a bolt at the bottom on each side that secures the rear seats in, I've got the Fire Extinguisher with 1 bolt (well its now an allen-key like bolt) going through the extinguisher then securing the rear seat.

Same here, only question is have you done AASA / CAMS events with it before? Just been paranoid, last thing I want is to get knocked back after driving to Shepparton.

4 bolts in the 4 holes of the mount into the floor pan and tunnel. why? because 4 will spread the load better and there is no chance of getting knocked back at a track day. bolting it to the seat mounts would drive me nuts if the seat is on rails as i cant see it not being in the way.

anyway, seat bolts are rather large and would do the job fine, and as al said, an oversize washer is a good idea, however as you said it could be the reason you get knocked back at a cams day. it all depends on the scrutineer you get and weather you drive a datsun ;) you will be fine at deca.

I have done an offical CAMS track day with the same one bolt mounting method and did not have any issues. I know Snowy used the same method for years, when his car was more street than track, and he never had any issues (as far as I know).

Same here, only question is have you done AASA / CAMS events with it before? Just been paranoid, last thing I want is to get knocked back after driving to Shepparton.

The one bolt setup your describing is the same way most of the motorsport guys do it, and have done at CAMS L2S events for 4+ years. This is how my car / snowys car runs at Dutton Rally with two extinguishers (one each side).

Basically if a scrutineer can grab the fire extinguisher and give it a shake and it doesn't move, you pass! So one bolt can do this and get you a pass, but what ryan is saying is correct, we all 'should' mount them better, and if a scrutineer does take a closer look then they would probably be within their right to knock you back. Bottom line is you will be fine for DECA and most of the time you will pass L2S sprint days. Just make sure that I can come along and see a metal bracket fire extinguisher mounted securely enough that I can't shake it loose (move the bracket). This is what I advise my scrutineers to check for.

Ryan - They are talking about the rear seat foot well (rear seat mounting point) not the front seat, so seat rails aren't an issue.

If we were all to rock up to a C3 race meet with this mounting system, I imagine we would all be going home early thou.

Or you do what I "maybe" used to do and when presenting for Scrutineering take the extinguisher out of the holder and keep it in your passenger seat. That way you can hand them the extinguisher to check the date (the main thing they want to look at) and if they ask where it is bolted just point and then they can't "shake it around" and complain. They will just look at it and say OK.

Thats what I might have done for years and years without a problem :P

(This was for the 1 bolt rear seat footwell jobby)

The one bolt setup your describing is the same way most of the motorsport guys do it, and have done at CAMS L2S events for 4+ years. This is how my car / snowys car runs at Dutton Rally with two extinguishers (one each side).

<cut>

Ryan - They are talking about the rear seat foot well (rear seat mounting point) not the front seat, so seat rails aren't an issue.

<cut>

If we were all to rock up to a C3 race meet with this mounting system, I imagine we would all be going home early thou.

Understood with C3 events, thanks for the information there, just wanted to confirm that I'm not doing something stupid by using only 1 bolt, and I don't exactly intend on real racing :)

Ryan, there is 1 bolt on each side securing the bottom section of the rear seats, ie. just behind the driver/passenger seat, under the rear seats, there is a bolt that secures that bottom cushion in, that's where I'm bolting too.

Due to the way the Fire Extinguisher is designed I've drilled the top / bottom hole out, the middle section is where the hinge is so it can't be drilled there, as long as the bolt is tight it should be secure :banana:

Or you do what I "maybe" used to do and when presenting for Scrutineering take the extinguisher out of the holder and keep it in your passenger seat

Well what I may or may not do may be the same thing :)

Excellent idea.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...