Jump to content
SAU Community

Recommended Posts

Hi, at Unique Autosports day i was told to cut the wire that does the auto lock of the doors as people who are stealing the car flick the lock switch and unlock the door.

anyway my friend has taken the door switch part off my door however we cant work out which wire to cut :) and i dont want to cut the wrong one :D

what colour is the wire that i cut?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/19798-door-unlock-button-urgent-help-plz/
Share on other sites

G'day dude,

Yepp, it's strongly advised to do this.

I did mine and from memory it's a brown wire that you cut. Or a wire with a brown stripe on it.

Cut it so you have enough left so you can join it back up. So if you do cut the wrong one you can still join it up again.

When you've cut the right wire, the button will still lock the doors, but won't unlock the doors.

Cheers

Jayson

Originally posted by Jay95R33

When you've cut the right wire, the button will still lock the doors, but won't unlock the doors.

Cheers

Jayson

wait....i'm confused:confused:....so how'd you get out of the car? :confused:

:confused:you mean the switches on the inside?:confused: how'd those thieves flick it from the outside? :confused:

Aero - there is a switch on the drivers door that you press and it will lock/unlock the passengers side door.

I'm not talking about the the drivers door lock, I'm talking about the other one that is there.

If you cut the wire to the button, you can still just unlock the doors manually etc.

Cutting the wire does not affect the central locking in anyway.

J

you can put an unbent coat hanger through the gap where the glass touches the roof and flick the switch, then u can get in the door without breaking the glass, and maybe w/o setting off the alarm. but hopefully it should go off as soon as someone inside the car moves.

Is that switch on the right hand side meant to lock both doors?? Or just the passenger one, because my switch only locks the passenger door.

That feature in my car comes in handy simply because I drive the car a lot by myself. Whats the benefits in disconnecting the lock. I thought it was quite a good function.

And how can people trying to hyjack the car, unlock the door? I'm a bit confused here!

NismoGirl - with the wire cut you can still lock the door, but not unlock the door.

You can still unlock the pass' door by unlocking the drivers door and the central locking will then unlock the pass' door.

I personally would my car as hard as possible to get into, so I have cut the wire. Sure my alarm will go off as soon as they open the door, but I'd like to make it as hard as possible to get the door open in the first place !

For an explaination of what can be done have a look at a5h's post above.

Cheers

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...