Jump to content
SAU Community

Recommended Posts

Hi fellow stagea owners I NEED YOUR HELP!!! My stagea was steaming up alot and had a bad smell coming in from the vents then i noticed a wet patch on my passenger footwell OH NO! water was coming in from up in the well!! Im sure its the heater matrix which has gone, so im wondering if any of you guys can tell me do i need a stagea matrix or will any of the skyline or any other nissan ones fit and if so is it a huge job to fit it or can anyone have ago at it?

Any help will be gratefully apprectiated thanks.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/
Share on other sites

hey your heater core has gone by the sounds of it

go into the engine bay and disconnect the hose that goes into the firewall above the turbo heatshield, just under around bonnet height. probbaly best if I take a photo to show it.

I have heard you can use a 300zx heater core, I ordered one months ago for $220 and have never seen it (better check my visa card actually) so i cant confirm.

My local radiator peeps have quoted me $450 to rip out the dash and put back together, plus the core which is $500 from japan with new brass fittings

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539171
Share on other sites

it's a biatch of a job!

i took mine out of my R33, and even with no intentions of putting the dash back in, it was quite a job.

you basically have to remove the entire dash, and everything in the way of the core...

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539175
Share on other sites

dunno about a skyline one fitting, although the dash is a very different shape, but heater cores are pretty much the same regardless of make or model aren't they? You will only be restricted by inlet/outlet size, and what will actually fit in the hole left by the other one.

as for it being a hard job? To be honest, not really. It is a long, involved and fiddly job, but there is nothing that is very technically demanding about it. Same as everything else, if you take your time, pay close attention to how things come apart, and bag and label everything you take off, then you will be fine. I do recomend that you have a digital camera on hand to take photo's as you go - this can be an invaluable tool when it comes time to reassemble.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539268
Share on other sites

Ditto on what Stinky Rooster said.

I've done this on an R31 Skyline and VC Commodore, except had A3 pieces of paper

on the garage floor with bolts laid out in position relative to the dash position.

Took 5-6hrs taking my time on a Saturday with a few ciggie/drink breaks in between.

Do it yourself take your time and save $$$$.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539865
Share on other sites

Looked into this and was told by a well known Skyline tuner in the UK that the heater Matrix will come out into the passenger footwell. They reackon no more than a couple of hours to change !

Don't shoot the messenger as I have not done it myself yet.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3540470
Share on other sites

Looked into this and was told by a well known Skyline tuner in the UK that the heater Matrix will come out into the passenger footwell. They reackon no more than a couple of hours to change !

Don't shoot the messenger as I have not done it myself yet.

YEAH, I have heard that in an auto you can get to the heater core thru the glovebox area, but need to disconnect air conditioning and regass afterwards.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3540494
Share on other sites

yes i can say taking the dash apart is a killer of a job, finding all those damn screws and clips is a job in itself :rofl: Good luck, dont forget there is a couple of screws in the demister vents and they are hard to see unless u look through from the outside of the windscreen. These 2 bolts prevented me removing the dash for a day as i couldnt work out for the life of me what was holding it on

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3547241
Share on other sites

  • 1 year later...

Ive just taken my heater matrix out by removing the glove compartment then the a/c unit.

Its easy.You will have to get the a/c unit regassed. you can give the a/c unit a good clean as its out, mine was quite mucky.

http://www.skylineowners.com/forum/showthr...ighlight=heater

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-4987550
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...