Jump to content
SAU Community

Tomei Pistons

NYTSKY

By NYTSKY,
in Engines & Forced Induction

 Share

Recommended Posts

NYTSKY Grand Master

NYTSKY

Posted
Posted

I just found some Tomei pistons that i might purchase,but before i do i would like to ask some questions:

Its for an RB25DET

These are the specs of the pistons:

Bore: 87.0mm (Will this be big enough? Allowing for the bore to be honed.Or will i need to go 20thou over?)

Pin Dia: 21mm

Recess: Nil

Ring: Standard(I think this means they are not Titanium coated.But are still Tomei rings.)

CHEERS

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
bore size will depend a lot on the condition of your block. have you pulled the motor apart yet? your engine builder will be able to recommend which one to go for.

The motor is not apart yet.

I could only see that the seller only had the 87mm pistons,so i was wondering if this would be big enough,allowing for the bores to be honed.

Stock bore in a RB25DET is 86.5mm isnt it?

So having the 87mm pistons would allow for .5mm to be cleaned up.

or is this a too small of a margin to go off.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3552156
Share on other sites
BLN215 Rookie

BLN215

Posted
Posted
Thats awesome.40thou is heaps i cant see why my builder would want to hone more than that.Motor is in great condition.

It'll depend on the condition of your bores as to how much will need to be bored/honed out of it.You'd be best to have the engine pulled down and inspected and/or machined before you shell out $1300+ for a set of pistons that you dont know if you'll need.

Just the way i'd do it :)

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3554956
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
It'll depend on the condition of your bores as to how much will need to be bored/honed out of it.You'd be best to have the engine pulled down and inspected and/or machined before you shell out $1300+ for a set of pistons that you dont know if you'll need.

Just the way i'd do it :)

Well i want to buy the pistons anyway.I should think 40thou over for the pistons should leave plenty of room for honing.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3554958
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted

The seller only sells the pistons in 87mm.So i think that the 40thou over will cover me incase of poor bores.If my bores are in good condiiton,would an engine builder charge more for the bores to get...Bored?

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555149
Share on other sites
BLN215 Rookie

BLN215

Posted
Posted (edited)
The seller only sells the pistons in 87mm.So i think that the 40thou over will cover me incase of poor bores.If my bores are in good condiiton,would an engine builder charge more for the bores to get...Bored?

If your bores are in good condition then you'll be using an oversize bore you dont need too and wasting perfectly good metal that could be needed down the track.You may only need a 20thou over bore so your using 2 overbores when you dont need too leaving you with less life in the engine block/sleves.

But if your determined to get them go for it,just remember were only trying to help you out here.

Edited by BLN215
Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555158
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

always go for the smallest oversize possible. far better to pull down the engine first, inspect. then buy pistons to suit your new bore size. if there is nothing really wrong with the motor you should be going for 86.5mm bore. .5mm oversize.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555276
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
always go for the smallest oversize possible. far better to pull down the engine first, inspect. then buy pistons to suit your new bore size. if there is nothing really wrong with the motor you should be going for 86.5mm bore. .5mm oversize.

In that case i think it would be a better idea to get the pistons in Oz then.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555283
Share on other sites
fEkuaR Experienced

fEkuaR

Posted
Posted
In that case i think it would be a better idea to get the pistons in Oz then.

Definately a better idea. Your engine would be absolutely stuffed if you NEEDED 40thou oversized pistons. Also if you dont go large oversize now you will be able to use the block again if need be in future re-builds. A block can only be taken so far out.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555635
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...