Jump to content
SAU Community

Recommended Posts

Evening fellow car lovers...

My car - R33 GTST

Recently i did the following modifications... upgraded to R34 GTT intercooler, installed Turbo Smart Dual Stage Boost Controller (switch mounted in cabin to switch between a high and low boost setting) and a Drift Boost Guage. Installed everything myself...

Now... with the boost controller at its minimal settings (as low as the dials can go), im getting 2 different boost readings between the factory guage and the aftermarket one. I installed the aftermarket one onto the thicker hose commin off the intake manifold goin to the fuel pressure regulator (so the guages are taking readins of opposite sides of the intake manifold).

Stock guage is telling me about 8-9 psi... aftermarket guage is telling me 0.75 bar... thats like near 11psi??

Why/Which is correct??? :down: lol in oversight whats the point of having a dual stage boost controller if at its low boost setting its already at the limit of the factory turbo :D (i wasnt planin on upgradin the turbo)

Any input would be greatly appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/199271-different-boost-readings/
Share on other sites

Firstly, a gauge is only as good as the manufacturer. It's not beyond the realms of possibility for 2 different gauges to give 2 different readings of the same thing. The Nissan factory gauges are notoriously inaccurate, though.

And a boost controller cannot lower the boost below standard. It can only raise boost above standard.

Firstly, a gauge is only as good as the manufacturer. It's not beyond the realms of possibility for 2 different gauges to give 2 different readings of the same thing. The Nissan factory gauges are notoriously inaccurate, though.

And a boost controller cannot lower the boost below standard. It can only raise boost above standard.

Like the man says, if you are concerned get your aftermarket boost gauge calibrated.

Cheers GW

The aftermarket boost controller, should be able to get boost BELOW 7PSi, if installed correctly.

The factory actuator is only a 3PSi setup.

The question is, did you remove the factory solenoid?

Also, have you removed the ball and spring from the Turbo Smart tee-piece?

Those boost controllers aren't that great... I ran one, switched for the little $20 boost controller and haven't looked back!

The aftermarket boost controller, should be able to get boost BELOW 7PSi, if installed correctly.

The factory actuator is only a 3PSi setup.

The question is, did you remove the factory solenoid?

Also, have you removed the ball and spring from the Turbo Smart tee-piece?

Those boost controllers aren't that great... I ran one, switched for the little $20 boost controller and haven't looked back!

Uhhh no Im pretty sure the stock R33 GTST actuator is set at 7psi...

Have you ever actually seen a 33 hold 3psi on a stock turbo with everything functioning correctly?

I did remove the factory boost solenoid... and what spring inside tpeice???? lol i just hooked the tpeice between the turbo nd wastegate like the instructions said and blocked off the other top hose which went to the factory boost solenoid... nd yeah at its minimal settings its at like .75 bar lol

What sort of things would i need to check to see if anythin went wrong in installation?? Im pretty sure i did everything correctly though cause it all works lol

Uhhh no Im pretty sure the stock R33 GTST actuator is set at 7psi...

Have you ever actually seen a 33 hold 3psi on a stock turbo with everything functioning correctly?

Yeah the stock actuator is two stage. 5psi to 5000rpm then 7psi to redline :thumbsup:

I take it that your Drift boost gauge just a cheap knock off, in which case its properly as useless as the stock one. Go out and get a proper brand gauge, personally i wouldnt use any thing less than autometer (not autogague) so that means around the 100-150mark depending where you get it from, if you want to spend more on apexi and the like thats all good, you'll probably get an even more accurate reading but in your case an autometer should serve you well.

If you have the basic breathing mods done, ie fmic, turboback exhaust and filter than on low boost with no solinod you should be around the 6-7psi mark.

The location on the manifold where you get your vacuum/boost reading doesnt matter as long as its definately a manifold feed.

LOL, where do you go about getting boost guages caliibrated?

Nearly missed this, first off gauge needs to be cabable of being opened without terminal damage being inflicted. (best option) if not can get correction chart? The yellow pages is always a good place to start, mechanical gauge range = press - 0 - vacuum, electrical = take sensor also. Any NATA instro calibration company or connections to airforce/airlines/altimeter calibration joints, know anyone in the sky-diving game.......breathing? :thumbsup:

Cheers GW

Heya, i dont think the drift guage is faulty, it sells for 90 bux... nd is pretty lol...

I havent done air intake or exhaust mods yet... pod filter is on its way from ebay :banana: nd exhuast wont be for a while. Ahwell i dont really need the turbo to boost more than it is at the moment anyway lol, after i get the exhaust and a safc ill get tuned on a dyno and they can look at it then :down:

thanx for input guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...