Jump to content
SAU Community

Recommended Posts

im pretty sure some manufacturers design the bonnet so when there is rain there is a little cover they provide...and you can cover up the vented spots so water doesn't it in or the vent my be designed so when there is rain the rain will be directed to the radiator? or something? hope that helps :P

Cheers

Chi

Mate, let's face it... you want a vented bonnet for the 'agressive look' - as engine bay was, you got all the air you need.

I've done some research into this and unless the vens are face diagnally as in - it's leaning towards the front and it has some sort of cover on the top for running falling directly down, run + engine bay is no good. Especially, think about it, what if it's raining heavily? Then you're buggered.

Think twice if you want one and make sure you choose the right one.

Good luck.

just make sure you get one with a drop vent towards the front and not the rear of the engine. the area between your radiator and cam covers is safe for contact with water... further back you could short out your coilpacks, your PTU, etc.

I have this on mine and it came with a Cover inside for the vents for the winter and Wet days....But for summer i'll pull it out although in Scotland thats normally one day a year if we're luckly lol.

It's in carbon and was supplied by the lads at www.knight-racer.co.uk

skyline0.jpg

there is too much crying go on on this site.... if you want a drop vent hoood get one.... its not going to ruin your engine.... i have one its fine and it actually has overlay fins which prevent a half inch of water from coming in..... of course if you are leaving your car out in some sort of flooding rain storm then you had better not get one haha

ventwheelssuspensionmt6.jpg

sorry this is the best pic i have of my vent. Hard to see but there are little fins that stop it from draining straight into your engine bay.... believe me they hold alot of water the hardest part is trying to get it all out after you wash it haha

i guess it all depends on what sorta vents you're looking at... bonnets with drop vents let water thru easily while the raised vents like the two above have some preventative bits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...