Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

They rank up there with fake bov's... but if you're dead set on looking like a tool, goto any nos or nxexpress installer and ask them to hook you up with a CO2 rather that Nitrous Oxide purge kit.

Might as well go all out get the Nitrous Oxide nozzles installed and a bottle warmer, at least it won't be all show then >_<

he didnt ask you what you thought of it. Or your flaming.

He just asked where he can get it from..

All of you guys just jump on the bandwagon and start flaming because YOU think it's gay.

tis called freedom of speech my friend, maybe we could talk some sence into him

he didnt ask for your particular opinion on flaming in this thread either but you still gave it

lol

install a t-piece on your radiator hose. install a thin heat resistant tube into said t-piece. run this tube into a windscreen washer nozzle. drive up and down the road at really high revs till your engine's really really hot. activate nozzle. watch as your ghetto fake NOS inflicts damage to your car's paintjob and delivers amazing 3rd degree burns to your face. it'll cost you about $20 in supplies. good luck.

install a t-piece on your radiator hose. install a thin heat resistant tube into said t-piece. run this tube into a windscreen washer nozzle. drive up and down the road at really high revs till your engine's really really hot. activate nozzle. watch as your ghetto fake NOS inflicts damage to your car's paintjob and delivers amazing 3rd degree burns to your face. it'll cost you about $20 in supplies. good luck.

fknlol! :woot:

LOOOL :P

is it that bad??

woops, i didnt know... lol...

I was just thinking of the 2F2F movie, and finally found out what those systems are called. :D

From what i know the only point of a purge valve is to purge air and vapour out of the lines so that the liquid nos fully fills the lines... Its basically only used (properly) by extremely high end drag cars which need every last bit of performance.

Most people who are into performance cars know this, so therefore when they see a dude in a stock looking R33 purging what appears to be nos, they instantly think -POSER- Your car doesnt need that mod for any reason other than to try to look cool.

To make matters worse, you're talking about putting a FAKE version of a pointless modification onto your car. Thats twice as bad! :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...