Jump to content
SAU Community

Recommended Posts

hey guys

just wondering, is there a table or conversion method to work out what size injectors can support what power (hp)?

i did a quick search and it has been suggested that 1cc supports roughly 1hp, so 700cc inj supports around 700hp

some1 also came up with; cc x 6/5 = hp (700cc x 6/5 = 840hp), which seems quite high

please confirm :)

cheers,

Andy

Edited by andz
Link to comment
https://www.sau.com.au/forums/topic/200355-injectors/
Share on other sites

stock gtst injectors and a FPR will do 250rwkw

well i've already bought the injectors and fuel pump, and i want some breathing room in the event that the high flow makes much less than 250rwkw and i get bored and decide to strap on a bigger turbo :( . but i wouldn't be aiming any higher than 280rwkw, cause i can't afford a rebuild :) . so the 440cc injectors should still be up the task

Link to comment
https://www.sau.com.au/forums/topic/200355-injectors/#findComment-3565475
Share on other sites

so why is it that i've read articles in hpi etc that have cars with a power output of about 500rwkw but they're using 1600cc injectors?? do injectors still work accurately even when they're being used below the level they're designed for?

Link to comment
https://www.sau.com.au/forums/topic/200355-injectors/#findComment-3570780
Share on other sites

Personally I would not want to be using any injector (or fuel system for that matter) at more than MAX 85% of its capacity. In case shit happens, it is probably a good insurance. (having said that how anal and redundany you want / need to be with your fuel system depends on what what your doing with the vehicle and how far you want to take things), $$$ add up quickly :D

Link to comment
https://www.sau.com.au/forums/topic/200355-injectors/#findComment-3570862
Share on other sites

yea mate but how many 1600cc squirters are they using??

many racing/high performance cars use big injectors to suppliment their apetite. they are called 2ndary injectors. and it is very common in rotors. e.g. they may be using a few 500cc injectors then use a couple of 2000cc injectors to beef up the support.

i personally dont know y they do it. perhaps using all 2000cc squirters may be too expensive or inefficient....

im sure someone on here might know?

Link to comment
https://www.sau.com.au/forums/topic/200355-injectors/#findComment-3571162
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few things that seem a bit off here. - why is there 2 BOV’s?  - the turbo smart BOV on the compressor housing, is it turned up ALL the way? I have seen this become an issue on old man Pete’s car. It would push open and recirc, turbo speed would rise and the boost pressure would do weird things. - stock head? Does that include springs? - tried a different MAC valve? Is it plumbed correctly?
    • Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
×
×
  • Create New...