Jump to content
SAU Community

Recommended Posts

i have a electronic boost controller (Greddy Profec B Spec 2), and the cars pretty much stock except a cat back exhaust. im having a top boost of 11psi but it drops to 8.7 nearby redline. what do you guys think the problem is?

I don't think i have any boost leak as i dynoed it to check and the unique auto sports guys says its normal for the stock turbo but they also said a cat back exhaust will help the boost drop less, but it didn't do that.

What do you guys think the problem is? i really want a full 11psi boost to redline.

by the way the car is GTT R34

Edited by 10MinuteCar
wait im so newbie that when you guys always say front pipe i don't get what it is. i know the dump pipe is the single pipe from turbo to the cat but wats a front pipe??

dump pipe is straight off the turbo, which leads into the front pipe which is just before the cat. aka dump/front pipe. u can get it in one peice.

do everyone drop 2 psi on higher than stock boost? even with a eletronic boost controller as well like myself?

I use to have a case where my rubber intake collapsed causing the boost to drop once the engine bay was warm, and with the silicon intake pipe I purchased, IT MADE IT WORSE ended up going back to the stock intake, and reinforcing it with stainless steel off cuts. Problem solved.

I think the reason why your boost is dropping is due to your restrictive exhaust system. Invest in a dump & front pipe and a high flow catalytic.

My 34 drops boost by around 4 pound on redline, i have the boost set to 14psi and by redline it drops to just below 10psi, get used to it mate if your going to keep the stock turbo

It is normal, altho mine is dropping from 14psi to about 11psi

get a free flowing full exhaust system as suggested before to help it breathe better

i would of thought that standard turbs would be able to hold 11psi but i guess not

is it possible to use a r32 actuator inconjunction with the EBC by any chance?

Yes but you would be wasting your time, I have a adjustable hks actuator and it still drops off boost

just a question ;) would a exhaust manifold leak cause the boost drop as mentioned before from about 11psi down to 9psi as well? or will it never even reach the 11psi in the first place?

Possible but it would need to be a big exhaust leak

just a question ;) would a exhaust manifold leak cause the boost drop as mentioned before from about 11psi down to 9psi as well? or will it never even reach the 11psi in the first place?

I just had my leaking manifold repaired.

Problem was low boost from low rpms. Once i put the boot in it was hard to notice because there was lots of pressure and i made the 11psi my boost controller was set to.

Manifold leak (depending how severe) shouldn't cause high rpm boost loss. Like all the fellas said, it's normal for your setup to lose 2-3psi.

I run a GReddy profec on my GTT also and have found that just playin with the gain setting in particular can help stop the boost dropping off in the higher revs. Im only running 10psi hi boost and still playin round with the settings but have managed to get it pretty good and hold the 10.

I also have a 3" system off the back of the turbo that prob helps a bit too tho.

Good luck!

I run a GReddy profec on my GTT also and have found that just playin with the gain setting in particular can help stop the boost dropping off in the higher revs. Im only running 10psi hi boost and still playin round with the settings but have managed to get it pretty good and hold the 10.

I also have a 3" system off the back of the turbo that prob helps a bit too tho.

Good luck!

oh great! since we're both using the same cool EBC :P could u gimme some advice on how to set the settings to hold 10psi boost please? from 1st step to last as ive never tried to touch the EBC myself but will do with the help of a pro :D

LOL i am hardly an expert!

Ive only had it on there for bout 2 or 3 weeks and been playing with it tryin to get it somewhere right.

just went and had a look at my settings and atm they are-

set: 40%

gain:27

set gain:6psi

its holding boost pretty well but needs more fine tuning. also been hard cause ive been trying to do it on my own...

My cars mods are just 3" turbo back and a K&N panel so pretty stock...

hope that was of some help to ya! :P

oh also just adding the peak boost with those settings was 10.3psi....not sure of the rpm(bit hard to drive and look at it lol)

Edited by jase-r34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...