Jump to content
SAU Community

Does Any One Know How To Remove Rear Spoiler R33 Gtst

SeanR33

By SeanR33,
in Exterior & Interior Styling

 Share

Recommended Posts

bluey33 Experienced

bluey33

Posted
Posted

Yea i had to do it to change SI spoiler to SII.

Dont have time to write it up here but ill put it up tonight if possible.

Basically open your boot. Pull Fabric back and find the nuts to undo. i think there is 4. if not then its 2 (did it ages ago)

once they are undone then you have to slide the spoiler back and forth to get it off the clips. This part was to fiddly and i ended up breaking a couple of them. thats basically it.

Ill put up pics of back of spoiler thats off to show ya what i mean if i can find the time

waza Collaborator

waza

Posted
Posted

Easy as, take off about a dozen clips(very easy to pull off with flat head screw driver). then use the flat head to take of 4 plastic grommets off. 2 on each side. then remove 2 screws (10mm) on each side. dont worry it wont fall off. then just simply fiddle with it a bit and your done

:D EASY :)

tm_r33 Experienced

tm_r33

Posted
Posted

had mine off not long ago.. once youve undone the four bolts, put both arms under the wing and lift up as hard as u can... the thing is surprising strong and even though u will have to jerk upwards quite hard nothing will break

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

      Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...