Jump to content
SAU Community

Recommended Posts

Supercharged, nice i like the setup... Looks very different and for some reason im turned on by it :rolleyes:

But as everyone said is not going to be too fast and your fuel mileage will be pretty shocking as those thing weight a bit...

Not to mention they dont stop all that well... However that all said horses for courses...

If you want a go fast stop quick semi street/track car than keep the r33

if you want a cruiser, comfotable, luxury (in comparison to an r33) to spare and a nice v8 tone, then swap it

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Supercharged, nice i like the setup... Looks very different and for some reason im turned on by it :rolleyes:

But as everyone said is not going to be too fast and your fuel mileage will be pretty shocking as those thing weight a bit...

Not to mention they dont stop all that well... However that all said horses for courses...

If you want a go fast stop quick semi street/track car than keep the r33

if you want a cruiser, comfotable, luxury (in comparison to an r33) to spare and a nice v8 tone, then swap it

Brings back memories doesn’t it Col, haha! Mine was a real Lexus so I got snob rights though.

To be honest buddy, go with what people are saying. Keep away. They are very expensive car to fix and maintain and do use quite a bit of fuel.

I had a few little mod’s done to mine, and stripped the trim out and I was beating stockish R32’s, S13’s from 110kph roll on, so hardly a performance fun machine.. We wont start on trying to stop one from decent speends on those silvia size brakes they come with either,

I had no end of electric problems and running gear problems. I stopped counting at $11k in work I had to spend over almost 2 years ownership. $3k of that was on a gearbox reco as it let go.

Fun cruiser and the 1uzfe sounds hot with a decent exhaust, but they are just getting too old with too many little problems that add up quick.

Celsior is not a downgrade, it's an upgrade, luxury, comortable, VIP cars..... The 1uz engine is fantastic. Torquey, smooth, hell reliable.... 190kw stock, supercharged it would be pretty quick.... The v8 sounds FANTASTIC.....

But if it is sold, swap for the aristo. Definately. There really is no match for a 2jz

If your not driving stoopid and have a good driving record you have a good chance of being left alone by the cops, keep the line, you have put too much into it to just give it away for a song. I do like the Aristo's though, 2jz, comfort and Toyota reliability, not that Nissan isnt but all my Toyotas were really hard to kill lol.

My ls400 has done 290,000km and zero electrical problems other than the lcd on the climate control which was designed poorly on all models. Like most jap cars, electricals usually aren't a problem.

That said the ls400 handles like poop, and it's not fun until 100km/hr+. It's almost impossible to break traction for instance or go sidewise due to the auto. Also the brakes are underpowered for the a 1700kg car, and the discs warp if you regularly brake hard.

I wouldn't pay any more than $10k for one these days..

well it's got an upgraded gear box in it rebuilt motor and everything when it got supercharged... it's got 356rwhp so pretty towey... i'm tossin up wat to do i'm also lookin at a ford explorer or somethin anyone wan2 swap there car or buy mine outright make me an offer

Edited by redevil
ford explorer

They renamed it to "Ford Exploder" after many 1998-2001 model explorers caught on fire for no aparent reason...

Ford had to recall nation wide to replace the A/C's electrical system in the car as they suspected this to be the fault, months later they were still catching on fire... :huh:

I might be a little late to post here. I might just add my thoughts.

I drove this car pre and post surgury (ie. the supercharger). I can certainly say coming from a gtr background that this car was a beauty. (1) for attention (2) for the drive. It has space, reputation, and luxury. If the owner hasnt played with the seat settings, my personal settings could still be preset. The owner at the time looked after this car really well and was very particular in the way it was presented. I cannot vouch for the new owner but by the looks of it, it hasnt changed.

This car is fantastic and if money wasnt an issue i would have my gtr and this celsior.

Hope that helps.

Good luck.

Edited by arbess

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...