Jump to content
SAU Community

Recommended Posts

Hey all,

Went to calder last friday for the 1st time and and ran my car a few times, was wondering what sort of times other similiar cars was getting as i was going up against 11 sec cars!

My car and Mods:

1993 R33 Gts-t (Auto)

Performance mods:

Apexi N1 catback Exhuast

R34 Side mount cooler

running 9 Psi

Tyres: 17 inch rims with 245 continental tyres (about 60% thread) 22 PSI

and everything else is pretty much stock. Not tuned or anything like that.

My best time was:

14.29 @ 157 km/h

most my times was between 14.3 and 14.6 - i had about 11 runs.

I found that the car would launch hard but then die in the last 100 meters :D

i would be very happy with that time.

our skylines up north just cant seem to push the same times. different track and maybe the prep will probably be part of the reason.

what 60ft time?

hmmm really? the weather could also play a part i guess....on friday (when i went) it wasnt too bad, track temp was about 24 degrees..

60ft time was: 2.11

660' - 9.12 @ 125 km/h

That's a good time.

Are you planning to go quicker?

ye id love to break into the 13 seconds... and then i will be happy.

My car is a daily driver, ive had it for about 5 years and i've done 110,000 km's on it since ive got it...

I rekon maybe with a FMIC, high flow cat + dump pipe i could improve the top end a bit and maybe break into the high 13's!

But at the same time, as it is now, its great for day to day street driving / over taking and quicker off the line than more modified / tuned manual R33's of some of my mates and i don't know if i want to lose that to gain a few milliseconds on the drag strip!

What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

60ft time was 2.11

thanks for the tip! ye i'm def going to invest in making the exhaust to turbo back me thinks!

Justjap have a nice deal going for you:

http://www.skylinesaustralia.com/forums/JJ...RB-t204414.html

So much cheaper than I first thought, wouldn't take more than an hours labour if it is a straight fit to your existing cat-back exhaust so you should be able to have it fitted for about $500 all up.

is it losing traction on launch?

being auto and stockish, I don't think it would.

anyway.

to get something like a 13.9 (in to the 13's as you're said).. get the exhaust finished (dump pipe and front pipe in one and a new large cat).

then get an SAFC and have it tuned.

Even the blue screen SAFC would get you a good increase in power, especially in the upper end.

the Blue screen ones would be below $300 now for sure.

dump/front pipe in one can be picked up for about $200 from a number of places brand new.

SAFC tune will probably set you back about $200.

all of that easily under $1K.

should push power to near 190rwkw.

should net you 13.xx

if you are losing traction on launch, then look in to tyres too.

I would also race with 16's instead of 17's.

I dare say that your 17's with tyres would weigh more than the stockers which weigh 16kg with tyres.

EDIT - don't replace the R34 SMIC with a FMIC.

you will lose the response that you love at the moment.

it is more than up to the task.

If the R34 SMIC doesn't have any ducting to it, I would look in to making one for it.

Water spray is another option but probably not needed.

Edited by GTST
What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

his current mph is more like 97

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...