Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Hehehe, I've had a quick run with a GTS.

It was a rolling start from about 20km/h to 140km/h.

There was nothing in it upto about 110km/h then I was just (and I mean JUST) pulling away.

I was totally shocked as was the bloke in the GTS :D

At that stage I had a turbo back 3 inch exhaust, 12psi boost, and a pod with CAI !!

Oh - I've got a 1995 GTS-t.

Not bad for a car that is about 1/4 the cost ;)

J

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431047
Share on other sites

The Hsv r very crappy cars, they weight too much and dont have enough power holden really need to get them right. GTS-t should be able to hold them with not alot of mods.

The ls1 350 r around 300hp (if i remember right) they should be Mid 13second 1/4mile but they never are more like mid 14, so GTs should hold it and GTR should take it

All depends on drive, weather condition but the skyline should have the upper hand

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431083
Share on other sites

Originally posted by playa

JAY95R33. lol u were pulling from 110km/h onwards... Geez GTS's aint that bad are they??

Yepp just. When I say just I mean about half a bonnet length !! So there really wasn't anything in it.

The GTS's are very heavy. Something like 1680kg's (someone correct me if I'm wrong here), compared to the GTS-t's at about 1380kg's.

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431096
Share on other sites

Originally posted by Soulja

By the way if it is a mod Ls1 with AMerica Mod Parts then yes he could wipe the floor with gtr

You mean it'd win if it's against a standard GT-R...

If on the other hand, the GT-R is modded with Japanese parts, it's shit over the GTS.

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431343
Share on other sites

Originally posted by AVENGE

I dont care if your mod parts come from Uranus, on the street a GTS will never beat a GTR due to traction alone!

If anybody cares to prove this theory wrong, lets go! :D

oK TIME TO PROVE U WRONG hehehe (sorry about caps)

Lingenfelter Installed Engine Packages

1997-2003 Corvette Twin Turbo LS1, ZO6

550 BHP / 550 lbs-ft of torque

500+ rear wheel hp

Includes:

CNC ported cylinder heads

Three angle valve job, checking of spring tensions & heights

LPE custom camshaft

Two true ball bearing turbochargers

Two high efficiency air to air chargecoolers

Custom molded Samco silicone air ducts

4 into 1 custom exhaust manifolds

Two turbo outlet adapters

Turbocharger scavenge pump

Turbo oil drain reservoir

Two K&N 360 degree conical air filters

Heat shields and stainless clamps

Professional installation, testing and tuning

GHL stainless steel exhaust system

Turbocharger water feed and return hoses

Turbocharger oil feed and return hoses

Gaskets and fasteners

Chassis dyno report

2 year/24,000 mile warranty

This kit is build for corvette but as the GTS has the same block LS1, it will fit with a few minor mod.

I dont think you could get something like that in australia for a hsv :bahaha:

P.s This is just one of the many kits

350 CID LS1

350 CID Supercharger

383 CID LS1

427 CID LS1

550 HP Twin Turbo

650 HP Twin Turbo

725 HP Twin Turbo

and yes im pretty sure 1 of this kit would give a Jap Mod GTR a run 4 its money (who would win would be done to spec and dirver)

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431415
Share on other sites

no they arent drag slicks car, they r street vette with street tyres. i was just saying if a kit like that was add to a hsv gts it would beat a gtr easy but then again a mod gtr is hard to beat (i have seen some really nice mod R_34)

If i remember right The 8second vette with the trubo kit had street typers (or maybe it was the 9 second)

again just tring to prove a point not up for other flame war

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431471
Share on other sites

yes all that can be done no doubt with even street tyres i still believe you, but yes these kits cost money, and these cars are set up for drag racing with solis rear ends and usually mini tubs, (not all some) the most basic superchargers kit and all the essentials on a ls1 sets you back say 8g, spend that same 8g on a new r34gtr (apples for apples both new cars) and i bet the gtr wins again and i dont care if they are jap, german, english or aus parts...... Also dont forget there is about 30-40GTR's in japan that run low nines or 8's with street tyres... Not bagging the gts had one for a while there well dad did but, c'mon this thread is ridiculous its apples n oranges chalk n cheese one is a purpose built performance vechicle and one is a performance vechicle made from a purpose built fleet car, both have strong and week points but no need to have stupid arguements and prove you wrongs about them..

Link to comment
https://www.sau.com.au/forums/topic/20574-gtr-vs-holden-gts/#findComment-431494
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...