Jump to content
SAU Community

Recommended Posts

that looks good, should be nice and torquey. It good to see the more extreme conversions still happening.

I doubt there are going to be any turbos on the side of that, by looking and the room just some simple headers look to be a stretch, although if they could make the manifold come to the front of the car, you probably could stick one nice big single in front of the engine.

What car is this out of??

Edited by R34GTFOUR

The VK56 has a pretty bullet proof bottom end.

These things are out of nissan Titans that weigh between 2200kgs to 2400kg's or so and 15.4 sec 1/4 miles out of the lightweight? 2,200kg ones have been done stock. not bad for a full size truck with a 5spd auto-gearbox. People get them into 12's with a small shot of gas . lose 800kgs or so and how fast would you go? :D

the day my engine is knackered im gonna steal dads 400hp+ 5.7 v8 out his ss and put it in my line, the guy who tunes dads ss has a r33 with 5.7 v8 and he is so quick round barbagello,

That would be the Street Force R33 Skyline, that conversion was done years ago, sounds nice as though.

And yeah that car above with the R34 GTR front end on it would be the twin turbo R34 coupe that is bashing around the Drift Australia circuits.

Also in regards to the VK56 conversion, I've seen a couple of people bash around with the VH45DE motor, which would be the motor series before the VK (which are also quad cam alloy V8's that are also a shit load cheaper to buy) in a couple of nissan platforms.

The main issue with the VH45DE was the height issue, with most people resorting to cutting the bonnet open to fit it in. And also finding that a manual gearbox bell housing would have to be fabricated to fit up a manual box. I believe there is a R33 with this conversion floating around in the Naturally Aspirated section with an auto box. Think it has a blower as well.

There are only two V8's that I would bother putting into a skyline and thats the 1UZFE (4.0l alloy quad cam V8) which I wouldnt bother unless there was some sort of forced induction hanging off the side of it....... or the LS1 which are a tough motor as it is, TON'S of aftermarket support like off the shelf turbo kits and have a variety of strong manual gearbox's to bolt up to it. Not to say also that replacement motors are dead cheap.

  • 3 years later...

This engine is also out of a Nissan ARMADA 04-05 5.6L V8 DOHC

its a 4WD or SUV wateva you want to call it probley weighs a fair bit aswell

claimed 317Hp 385 LB-FT Torque.

Edited by HYBRID VL

i have heard alot of good things about the L67 V6 SC like its the strongest engine holden has ever built and stuff like that Guys running 10's with a twin turbo setup on standard internals also heard they are very hard to source and alot are fake standard V6 with a SC on top.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
    • Very hard to make out what you mean, is it the squarish hole with redline shockproof (probably) under it? Is that pic from on top of the engine with the firewall to the left of pic and engine to the right? Either way, spray the area liberally with degreaser and try again, maybe circle the part you are worried about
×
×
  • Create New...