Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

They obviously don't have too much mechanical simpathy in this magazine... "for 11s, hold the GTR at rev limit for 5 seconds and drop the clutch". Ouch! Otherwise, it's not a bad read... I'm interested to see Ignition DVD again when it has the next installment of the Tskuba trip of the Hi Octane GTR :laugh:

Did anyone else find it a bit weird them saying you only need 230rwkw out of a GTST to do an 11 second pass? Has anyone ran a 11 second pass with only 230rwkw?

I do know someone who had an R33 GTST with 210rwkw and ran a best of 12.0 with just a little wheelspin. Then, on what turned out to be his last run of the night, he hooked up really well off the line only to break a non-genuine uni joint!

did anyone catch the american r33 gtr on the ignition dvd. 1000hp of goodness and boy does that thing go. check out the in car shot when he dumps it on the street.

P.S. Blitz, your car is a absolute stunner. well done :)

Edited by Pal
Did anyone else find it a bit weird them saying you only need 230rwkw out of a GTST to do an 11 second pass? Has anyone ran a 11 second pass with only 230rwkw?

can be - if ur running front runners and Mickey Thompson or the like on the back

i know of a certain 33gts-t that has around 550rwhp and ran 11.4

one of the only times he ran MT's on the back he nearly sent it sideways into the wall

reason it doesnt run quicker is boosts too late (full boost by 4500rpm with *i think* 8000rpm rev limit)

anyway - gonna have to try to get the mag 2morrow then hey

I love getting the free ignition dvd each month.

The female hosts are stunners!... although the present one and the past one both look the same!!! I think they even have the same name and initials if I recall correctly; Kirsty Allen & Kirsty Ambrush ?....

Only thing is, I seriously question how much they both know about cars, other than just being a pretty face.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...