Jump to content
SAU Community

Recommended Posts

The past couple of weeks I've been unable to find Shell Vmax in my area (Wollongong to Nowra), no big drama as I usually prefer BP Ultimate. Now today BP was out of Ultimate... what's the go?!?

Doing some searches brings up comments here and there on the subject but there seems to be a lot of here say about the cause and how long this is gonna go on for.

Just wondering if any of you are having no problems getting good fuel, if so what area you are in?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/207467-wheres-all-the-good-fuel-gone/
Share on other sites

because the p[eople who work in servos dont know shit

I found the same prob was out to the local race track in SA, and all the servo's on the way out had 95... ended up putting that in + octane booster... but why the fark cant they stock 98!!!

because the p[eople who work in servos dont know shit

Exactly :laugh:

Plus, I can't be arse queueing up just to ask a question to which you'd probably get a useless answer.

I found the same prob was out to the local race track in SA, and all the servo's on the way out had 95... ended up putting that in + octane booster... but why the fark cant they stock 98!!!

Maybe I should buy some octane booster myself if this keeps up.

I have been told (and read) that there have been problems at the refineries, beyond that I don't know.

Caltex at Nowra has plenty of 98,my line runs better on shell or bp but when you have no other choice caltex 98 is better than nothing. :laugh:

Quite true :P

I had to use the Nowra Caltex last week.

I note that there is no BP in Nowra, considering the size of the place that is amazing.

I live in Nowra and can't understand why we don't have a bp,geez we have 1 little shell in town and the caltex at south Nowra.Oh hang on we have a United as well,I would'nt put that in my lawnmower.Oh well if the Caltex 98 runs out looks like i won't be going anywhere ,my 33 won't run on anything else,should of kept her stock much easier. :laugh:

I live in Nowra and can't understand why we don't have a bp,geez we have 1 little shell in town and the caltex at south Nowra.Oh hang on we have a United as well,I would'nt put that in my lawnmower.Oh well if the Caltex 98 runs out looks like i won't be going anywhere ,my 33 won't run on anything else,should of kept her stock much easier. :laugh:

:P

Hey, that wasnt your white 33 for sale on the side of the highway, sort of down near that United station last week?

:(

Hey, that wasnt your white 33 for sale on the side of the highway, sort of down near that United station last week?

No mine is rare as colour wise,granny green i would say,but then again i am a nanny he he. :D

Yeah... they're still using the same weeks old story.

I'm not truly convinced this is the real reason.

To me it makes no sense at all that a handful of failed catalytic units has this much impact.

Oh... all at the same time, mind you - And at different companies refineries as well.

Quite remarkable!

They would surely have some redundancy built into their systems in the event that some of their equipment fails?

I mean, this is a multi-billion dollar industry, not some back yard operation. The same problems still persist for this long?

Maybe they should, umm... fix it?

Perhaps I'm just too sceptical/paranoid, but I mean, come on.

Thanks for the link mad082.

heh, fair enough :)

Green ay? I wouldnt mind seeing a pic if possible.

Cheers

Main pc died lost every thing on there.Using laptop now,let me know when your down here again and i'll show her to you. :D

Main pc died lost every thing on there.Using laptop now,let me know when your down here again and i'll show her to you. :ninja:

No worries Humbla, I'm down that way every week or two but usually at short notice :)

(I'm just up the road in Kiama BTW).

Last week, Mr Samuel said he had "lost patience" with the oil companies, saying the constant high-price of petrol was hurting every Australian

oooh he lost patience, how fkn scary. FINE THE f**kERS TWICE THE PROFITS THEY MAKE FROM THE PRICE HIKES AND LETS SEE THEM LAUGH THAT OFF !!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...