Jump to content
SAU Community

Radiator Air Deflectors, New Group Buy (no 5)


Recommended Posts

  • Replies 113
  • Created
  • Last Reply

Top Posters In This Topic

Hi Ppls,

Sorry for the long time in getting this going, but there is light at the end of the tunnel.

I'm off to NZ next week, but when I return I'm all geared up to churn out some panels.

I haven't comfirmed pricing with my manufacturers of the ally (steel is going up rapidly) but I don't expect a huge increase, maybe a few dollars.

We'll see.

Bare with me and all will be well.

Cheers

Pete

I would like one for an R33 GTST Series 2 in BLACK thankyou.

Do you have any ETA's to when you can carry out the order?

Thanks champ,

Paul.

  • 2 weeks later...

Hi Gents,

I'm back from NZ this morning and will begin collating stuff for the order soon.

Thanks for your patience, the end is in sight!!

Cheers

Pete

hey i was wondering if i am too late for this group buy.

If not then count me in for a 33 GTST S1 no powdercoat thanks.

  • 3 weeks later...

Hi Guys,

I'm about to start in earnest.

Will get requote on material cost this week and see how we go.

Cheers

Pete

How much to have one fabbed up so that it fits a R34GTT with series one front bar... I want it extending all the way to the headights just like the GTR versions from Jap-land...

Can it be done, and most importantly, will you do it - premium price is not a problem (within reason of course)

How much to have one fabbed up so that it fits a R34GTT with series one front bar... I want it extending all the way to the headights just like the GTR versions from Jap-land...

Can it be done, and most importantly, will you do it - premium price is not a problem (within reason of course)

Yeh im keen for a similar setup to this but for nismo bar.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...