Jump to content
SAU Community

Recommended Posts

After shockingly noticing my stock boost gague almost reachng the +7 mark under "spirited" driving conditions, i decided that after doing the hard reads over the SAU forums, being the nub that i am with turbos, that close to 1bar wasnt the best boost to run on a stock R33 turbo ;)

So when the next Dyno day was organised in my area, i though it be a good plan to get a proper boost plot done over the entire rev range. Yeah, i could have bought a boost gague, or borrowed one but i didnt want to buy a shit one just to test it. Plus IMO its a little difficult to see whats going on when your driving. ;)

So anyway, on the Dyno for the 1st time. Wish i had have gotten it done in OEM form, then after each mod, but i didnt, so lets not worry :)

1998 R33 GTS25t

52,000km

HKS Silent Power Catback Exhaust

3" JJR De-Cat pipe (gotta love NZ)

3" JJR Split dump/front pipe

R34 SMIC

Apexi Power Intake

Stock "hi-boost" mod

SkylineDyno.jpg

Boy was i shocked when it crept up to, and surpassed 200rwkw. I was expecting high 180's-low190's. As that seemed to be the general result of previus R33's.

Ignore the stains, it deiced to rain later that day, i was excited with the result, but not THAT excited :yes:

And, the real reason for the dyno, the boost.

11.19PSi @ 5895rpm. I had decided that if it was over 11psi then i would do something about it, as i did NOT want to be at, or very close to the stock "limit" of 12PSi on such a low km turbo. Wanted it to last a little loonger! But im happy with the .19 extra. So here it will stay.

Boost plot pic wont show properly, so a brief description...

Dam does it spool quick, 8PSi by 2000rpm, then a steady creep up to 11.19PSi all the way to 6000rpm.

It hit speed cut on the dyno hence the sharp power drop, and a good foot worth of flame out the tailpipe. Ha. Love the RB.

Pretty happy with the result overall :)

Edited by gotRICE?
Link to comment
https://www.sau.com.au/forums/topic/208929-dyno-result-skyline-r33-25t/
Share on other sites

Just a small point of correction. Stock ECU doesn't actually have a boost limit...It has an airflow limit which is slightly different. The ECU doesn't even get a boost or MAP input...It looks at the maf (mass air flow) signal instead and if this gets too high it retards timing etc etc etc. The limit is also a function of rpm. As long as your air flow meter is in good condition and there are no leaks between it and you compressor inlet (ie extra air can getting in without the air flow meter registering it) you are pretty safe...Stock turbos get unhappy running above 12psi all the time though and will eventually give up...

Also the factory boost gauges are notoriously inaccurate..Get an aftermarket one...

Anyway glad you were impressed in breaking the 200rwkW mark...

.Stock turbos get unhappy running above 12psi all the time though and will eventually give up..

Yeah this is what i was more aiming at, what most people consider the stock turbos boost limit before it gets tissy :yes:

maybe i worded it poorly.

I'm a bit confused on a few things...

1) getting nearly 1400Nms?

2) If you hit speed/limit, how come it still goes past 7000rpms after hitting that limit? Looks more like a power/time graph ?

Anyways, anywhere around the 200rwkws is great, i know what it feals like (got the 98' too champ ;) )

I did a dyno run for the exact same reason as you too, and at the same level of mods.

Stopped at 12(ish) psi and got 196rwkws i think?

Now go get the Power FC and watch the smile on ya dial get even wider :yes:

LoL, you sound like a ecstatic new Skyline owner, or import owner :yes:

AWESOME to see someone happy with their car, its usually "f_ck me dry, my shits cutting out, dropping boost, using too much fuel etc"

Ride the happy wave ;) You only get desensatised, jaded and bored from here on in ;) :0

I'll be the first one to say it. I think your dyno might be a bit "generous", 213rwkw with stock management is a bit high imo. Also you say you did the high boost mod, that only atkes it to 7psi all the time correct? Unless you have a boost controller you cant go past that level, so is it really stock boost?

Not trying to rain on your parade or anything, just a bit confused.

Enjoy driving it either way!!

I'm a bit confused on a few things...

1) getting nearly 1400Nms? Divide it by the final drive :(

2) If you hit speed/limit, how come it still goes past 7000rpms after hitting that limit? Looks more like a power/time graph ? No idea :yes: Thats just what he said.

Anyways, anywhere around the 200rwkws is great, i know what it feals like (got the 98' too champ :P )

I did a dyno run for the exact same reason as you too, and at the same level of mods.

Stopped at 12(ish) psi and got 196rwkws i think?

Now go get the Power FC and watch the smile on ya dial get even wider :D

LoL, you sound like a ecstatic new Skyline owner, or import owner :D

AWESOME to see someone happy with their car, its usually "f_ck me dry, my shits cutting out, dropping boost, using too much fuel etc"

Ride the happy wave :D You only get desensatised, jaded and bored from here on in ;) :0

Yeah im stoked with it :O Skyline has always been my dream car, but i got stuck on the Honda scene, and fell in love with the Integra Type R and the track :wave:

I'll be the first one to say it. I think your dyno might be a bit "generous", 213rwkw with stock management is a bit high imo. Also you say you did the high boost mod, that only atkes it to 7psi all the time correct? Unless you have a boost controller you cant go past that level, so is it really stock boost?

Not trying to rain on your parade or anything, just a bit confused.

Enjoy driving it either way!!

Yeah i figured it is a little high. Its the way he runs it. Very strange, but thats the way hes always done it :s But when comparing it to other Skylines with similar mods, they were making high 180- mid 190's on the same dyno, so when "comparing" its still a fair bit more!

I barely take peak power as an indication, i tend to enjoy the gains per mod. But seeing as i was an excited little rabbit when i bout it, i modded it quicker than i could get it to the dyno :D

track it and find your MPH... Then i think you will realise the dyno is reading pretty high

I would have done it by now, but u figured trying to get a good time on the stock 205's was pointless! haha

I only just aqquired my Enkie RP-02's 8' and 9' a week or so before the dyno, so it was fantastic to be able to accelerate and actually move, rather than sitting on the spot wrecking tyres. Makes the car feel like a rocket ship after having the stockers for 6 months.

Cheers for the comments!

stock boost controller mod might give you 7psi, but the intake and exhaust mods (especially the decat) will increase that again.

maybe his ECU has been fingered while in it's homeland.

I did buy it completely stock.., but stranger things have happened i guess. Might even investigate it, but i highly doubt it. it didnt look like anything had been touched interior or exterior wise.

I would have done it by now, but u figured trying to get a good time on the stock 205's was pointless! haha

I only just aqquired my Enkie RP-02's 8' and 9' a week or so before the dyno, so it was fantastic to be able to accelerate and actually move, rather than sitting on the spot wrecking tyres. Makes the car feel like a rocket ship after having the stockers for 6 months.

Cheers for the comments!

Haha ahhh come on thats no excuse! Yeh the time would suffer but in fact your MPH will vary only ever so slightly one a run with great traction to a run with a terrible launch. In fact, 9 times out of 10 you worst launch will net your highest MPH at the traps.

Go out there and have a go, 215rwkw should be netting around 105mph im guessing?

Haha ahhh come on thats no excuse! Yeh the time would suffer but in fact your MPH will vary only ever so slightly one a run with great traction to a run with a terrible launch. In fact, 9 times out of 10 you worst launch will net your highest MPH at the traps.

Go out there and have a go, 215rwkw should be netting around 105mph im guessing?

Too true. Harden the F*ck up maybe? heheh

Yeah 105 sounds about right, i was trapping 99.9mph in my Integra R with 133fwkw, obviously wieght advantage.. but yeah. I think the local 33's trap around 105ish. I dont even think there is another drag day untill next season :D

wow, how light was the integra, a DC2R model? thats good trap speed. My r34 is trapping around 97 with 160rwkw, but its a porker!

Yaa DC2R. Such a beast of a car. Would own another one anyday!

Well, stock, they are around 1080kg. It was "track prepped" no interior, spare wheel etc etc, and 1/4 tank of gas. But added weight of huge calipers and rotors. Infact, that probly the heaviest thing, all the other mods, I+H+E would have reduced the weight a little. So probly similar to stock.

:):ninja::ninja:

Dont gimme that tone of voice :P Dont knock it till you try it hehehe.

R33silverS2'] [/b]what are your air fuel ratios like?

Didnt get a reading, was an extra $10 i SHOULD have spent :P Will get those next time, hopefully on a more accurate reading dyno. I know the other local dyno is more "true". But he doesnt often have dyno days, rather just uses his for tuning.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...