Jump to content
SAU Community

Nistune Powerfc Hks Fcon Haltech Ems Link Ecu Etc Real Time Road Tune And Dyno Tune Available In Sydney And Other State


Recommended Posts

I got my ecu remapped by toshi and the results are amazing.

Thanks Toshi.

Thank you Bahamasky.

He is living over sea and his car is fitting big turbo.

Mods:

FMIC

GREDDY PLENUM INTAKE

Q45 THROTTLE BODY

550CC INJECTORS

TOP MOUNT GT35R GARRETT TURBO

ACT STAGE THREE CLUTCH

TAIL BOV AND WASTGATE

STRAIGHT CATBACK EXHAUST

NISMO REGULATOR

HKS CONE FILTER

Im sorry I did not get your e-mail.

Toshi can u give ur email address i'll send it again, coz i sent u a long email before explaining the problems it was on ur profile where it says send email i sent it thru that plz check ur SPAM or junk email folder in hotmail or yahoo, gmail etc. it could be in there i cant send PMs reason not enuf posts.

thanks

Edited by sidewinder11
Toshi can u give ur email address i'll send it again, coz i sent u a long email before explaining the problems it was on ur profile where it says send email i sent it thru that plz check ur SPAM or junk email folder in hotmail or yahoo, gmail etc. it could be in there i cant send PMs reason not enuf posts.

thanks

My e-mail address and phone number is first of this thread.

[email protected]

  • 3 weeks later...

Im starting Power FC road tune by fc data logit (laptop computer).

Price $400

If your power fc is not tune yet , try my road tune.

If you are not happy with the performance, I will not charge.

0410490049

[email protected]

I sent remap chip to epigram and he got 265.4 RWHP or 197.98 RWKW (auto mission) on 98 octane.

His mods

Series 1 2 door R33 AUTOMAGIC

80k std RB25DET

std turbo

std injectors

std manifolds (in & ex)

Monsta FMIC

Bosch 040 fuel pump

Toshi Kubota modified and remapped std ECU

Tomei adjustable FPR set to 45psi@idle

std coils

NGK BKR5EYA special anti fouling plugs gapped to 0.8mm (no misfires!)

adjustable boost bleed valve set to max 12psi

std auto

std dif

http://www.skylinesaustralia.com/forums/Au...0&start=220

Thank you

  • 1 month later...
hey toshi

got a auto s1 stagea

should i get a shift kit fitted before a remap?

You do not need shift kit.

Hi Toshi

I'm keen for a remap.

2002 R34 GTT Auto

3 inch turbo back exhaust with hi flow cat

hypergear hi flowed turbo

cold air intake with K&N pod

Std injectors and fuel pump

Std intercooler (which i think is probably where the bottle neck is going to come)

I'd be keen for 220- 240rwkw, as i don't want to push the standard internals, any suggestions where to go from here?

I have my Toshi remapped ECU in my R33 Auto. I live n Brisbane, this was all done via express post and my dyno shop. It is the single best upgrade I have given my Skylne.

Performance is remarkable. Power increase, fuel economy better. AFR is steady, I dyno'd

my car and results are amazing! This guy knows his stuff!

My car is transformed, excellent service too, pleasure to deal with.

Highly recommended.

Hi Toshi

I'm keen for a remap.

2002 R34 GTT Auto

3 inch turbo back exhaust with hi flow cat

hypergear hi flowed turbo

cold air intake with K&N pod

Std injectors and fuel pump

Std intercooler (which i think is probably where the bottle neck is going to come)

I'd be keen for 220- 240rwkw, as i don't want to push the standard internals, any suggestions where to go from here?

I sent PM.

Thank you

I have my Toshi remapped ECU in my R33 Auto. I live n Brisbane, this was all done via express post and my dyno shop. It is the single best upgrade I have given my Skylne.

Performance is remarkable. Power increase, fuel economy better. AFR is steady, I dyno'd

my car and results are amazing! This guy knows his stuff!

My car is transformed, excellent service too, pleasure to deal with.

Highly recommended.

Thank you 1C3B3RG.

if you have any further queries, please feel free to contact me anytime.

I sent PM.

Thank you

Hi

I can't reply to your PM for some idiotic reason, because i am new here and haven't posted 10 times yet. I also can't message the administrators and ask them why, for the same reason.

Any way, yes there is a dyno shop nearby, but i don't know about the soldering part. How much soldering is there? I thought it would just plug in, in place of the old ecu?

What would need to be tuned on the dyno exactly,and would the people running it have the software to do it?

Regards

Nick.

hi, my r33 has been tuned by "car station" in japan.

Ive opened up the ecu box and there is a socket with a removable chip on the board.

If I changed my setup eg AFM and injectors could you supply a new chip for my box to run the new gear?

thanks

hi, my r33 has been tuned by "car station" in japan.

Ive opened up the ecu box and there is a socket with a removable chip on the board.

If I changed my setup eg AFM and injectors could you supply a new chip for my box to run the new gear?

thanks

Yes,Im able to supply new chip.

  • 1 month later...

I have a question.

If i already have the nistune board installed, and the nistune software, is it possible to just email you the BIN file, you do the adjustments and email it back and i burn it too the chip? This would save sending the entire ECU to you?

I have a question.

If i already have the nistune board installed, and the nistune software, is it possible to just email you the BIN file, you do the adjustments and email it back and i burn it too the chip? This would save sending the entire ECU to you?

If R32 or 34 it is possible.

But cost more.




  • Latest Posts

    • Biggest thing is you're okay!   It sounds like between the accident, and the drive home, it was a pretty torturous trip again! On the bright side, you took the opportunity to enjoy the event more from the perspective of a spectator, than as an entrant!   Sad to see so much damage to the car. It really has taken a HUGE hit in the front end. If/when you choose to repair, hopefully the rails are straight (At least from shock tower backwards). Hopefully the extra cage coming through there has save most of the chassis rails, and HOPEFULLY saved the motor too. Best of luck when you eventually get motivated to start pulling it down to check it all out
    • Sounds more like what Brad said, that it's mainly transfer. What pad bed in procedure did you use, and did you replace/machine the rotors, or just swap pads?
    • The stutter is almost entirely in the pedal. I don't feel the brakes release and reapply as you would with ABS engaging but the pedal feels that way, without the brakes releasing. It only lasts for less than a second and the pedal is fine again. It's hard to explain, sorry.  I'll get under this weekend and just double check everything is tight. Fluid is at max where I left it.
    • What bedding in procedure did you use?   When you say stutter, what exactly do you mean? Like it feels like someone letting go of the brakes momentarily and regrabbing them again to get you to stop? Re-reading your post, and that is what it kind of makes me think you're explaining, like theres a little bit of a jolt, likely just as you're reaching a stop. I've only had this issue once. And if its caused by what caused mine, you will want to get the car up on stands again and check it over. Mine was a case of a caliper mounting bolt coming out and letting the caliper rotate on the other remaining bolt and gave play in a wheel as it came to a stop. But not every stop either!
    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - then entered a hotlap with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
×
×
  • Create New...