Jump to content
SAU Community

Recommended Posts

well it might be actually possible, would need subframe off, sump off, crank out, balancer off, timing gear off, timing belt off, oil pump off, gearbox off, clutch off and flywheel off.

but if you did all that you could probably get to all of the bearings.

seriously though, if you need new big end bearings, rebuild the motor. the main bearings are probably in trouble, there is most likely some crap floating around somewhere, might as well do a hone and new rings while you are in there. pull it apart, clean and check it all, put it back together. so much damn work just to get the sump off

You wouldn't have to remove your crank to change B/E brgs. I've changed them on various other motors in the past by removing the B/E caps & spark plugs, pushing each piston up an inch and being real careful not to nick the journals with the thread on the B/E bolts, if you do, crank has to come out (might have to come out anyway for a grind or at least a linish if its got grooves).

You'll have to do a r & r on each cyl that's on the down stroke then turn crank to do others.....pretty messy this way but good oportunity to replace with a decent baffled sump.

As far as mains are concerned, they rarely fail unless there's crap in the galleries but usually evident by pitting or scratches on the B/E shells.

You CANNOT get the sump off with the gear box attached, there are two bolts behind the flywheel. This has been covered before, It is not practical to take the box out, to remove the sump. Just pull the engine, there is no way around it. And yes, I have done it.

Sorry to be a spoil sport

ok thats fine.... just wanted to find out first as i have never worked on a rb26 befor motor has only been rebuilt not long ago.... it got low on oil and now has the knock at around 3 4000 ill get some one to do all the work and check every thing

might be time for the bigger turbos at the same time :domokun:

You wouldn't have to remove your crank to change B/E brgs. I've changed them on various other motors in the past
You CANNOT get the sump off with the gear box attached, there are two bolts behind the flywheel. This has been covered before, It is not practical to take the box out, to remove the sump. Just pull the engine, there is no way around it. And yes, I have done it.

Sorry to be a spoil sport

Fair enough, its good info to know. As I stated above, I have removed sumps on various other motors whilst still in the car but not on an RB, thanks.

yes so have i thats why i asked.....it has cp pistions and a baffled sump ect all ready and light weight rods im not sure what type of bearings were used tho any ideas on how to tell?

Check numbers on the back of the shell, may give a clue, or if your not using them again light scrape on inside will tell you if they're copper leads or alu tins. Always a good idea to use a copper lead or similar in an RB though.

Huh??? Same thing....you gotta remove the B/E cap to remove the B/E brg. What sort of other B/E is there?
Where do you think the big end bearing sits, and what does it protect? The Big End (it's the end of the conrod that connects to the crankshaft).

If you are referring to the big end bearing, then call it that.

Where do you think the big end bearing sits, and what does it protect? The Big End (it's the end of the conrod that connects to the crankshaft).

If you are referring to the big end bearing, then call it that.

Been in the engine reconditioning game for 20 years mate so I appreciate you teaching me something that I learnt when I was still in nappies.

When engine reconditioners say they're changing their B/E's, they're always referring to shells. Otherwise they refer to the rods specifically. They never talk about changing B/E whilst referring to rods.

Sounds like you like to make a play on peoples words and argue pointless issues otherwise you wouldn't have asked such an obvious question.

Been in the engine reconditioning game for 20 years mate so I appreciate you teaching me something that I learnt when I was still in nappies.

When engine reconditioners say they're changing their B/E's, they're always referring to shells. Otherwise they refer to the rods specifically. They never talk about changing B/E whilst referring to rods.

Sounds like you like to make a play on peoples words and argue pointless issues otherwise you wouldn't have asked such an obvious question.

Sorry, didn't realise you had so much experience in these matters.

Yes, I can be a pedantic old bastard sometimes. It's just that there are quite a few younger members who don't always understand the technicalities.

And the only stupid question is the one you don't ask.

Sorry, didn't realise you had so much experience in these matters.

Yes, I can be a pedantic old bastard sometimes. It's just that there are quite a few younger members who don't always understand the technicalities.

And the only stupid question is the one you don't ask.

Yeah no probs bud, I know what you mean & I agree, its like banging your head on the wall sometimes. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Resizing injectors in Nistune can be done a couple of ways, and there are a couple of ways that you can make a mess of it. The tuner needs to be really aware of the effects of whichever approach he uses (either K, or TIM). They are both easy enough to "get the injector size right" to run the engine. But little details like old start enrichment and hot start are affected differently, depending on which boxes you check.
    • Pretty safe to say almost everyone that has tuned their own car has experienced this issue. The difference being that we have our laptop in the car and when it happens, it's literally 10 seconds of tuning to sort it.  Would you be happy to plug in your laptop and sort this yourself? It is a very simple process and there is no risk of harming your engine (if you are worried about that). 
    • Yeah thats the next step now, either they wil or i will take out for a drive to work and go straight their after work and see is we get the same issues 🤞  thought i try my luck here too, never know someone else might have had the same issue but thanks for the reply 
    • Basically your tuner needs to drive it for the 30 min (or whatever) to create the same conditions then check the ECU settings and sensors at that time. They may not be excited to because that takes them 30 min rather than just opening the bonnet and seeing the problem straight away.... Hot start is generally not as tricky as cold start, but there would be a table for fuel enrichment vs coolant temp as a starting point
    • Yeah, they all cant say anything for sure as everything is working fine . Said unable to find an issue untill it stops again. Could mist likely be CAS wiring or IAS valve issue but again not 100%
×
×
  • Create New...