Jump to content
SAU Community

Recommended Posts

lol imagine how complex abbreviations will be in 100 years. ilkbowgfctohg = i love kittens but only when george foreman cooks them on his grill. And your like an idiot if you dont get that.

Edited by MellowYellow
yeh boot drops easy. i would of thought that pressing ur bonnet in the middle would be the best spot... or are you's talking about the actual centre of the bonnet. Im think where the catch lock is put ur hand on that, shouldnt bend huh. I can imagine pressing from one of the font corners, stuff that.

I wana lift up a GTR bonnet now. sounds very lite. I can do shoulder press with my bonnet. Gona open up a new gym, no weights just skyline bonnets. haha

Yeah, I press in the centre as well, but not the centre, middle centre, if you know what I mean. :P

I press it down.

If you press it down where the catch mechanism is, there will be NO dents.

Dropping it just seems lazy and some times it does not always lock in and chances you might break the catch mechanism.

Drop it.

It's hard to press with the same force every time; and pushing that bit too hard will result in a dent.

Whether or not it dents you will end up with finger marks; whether they are noticeable depends on how clean it was to begin with.

Figure out the minimum height required to drop and securely latch your bonnet by starting at a 5cm drop and increasing by

a few cm each time till it latches. Gravity doesn't change by much no matter where you are on earth; so once you figure

the minimum height out it should not change. Lighter bonnets require more height :D

Regards,

Saliya

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...