Jump to content
SAU Community

Recommended Posts

I've got an auto R33 gtst-series 1 that I got recently, and my fuel consumption is about 280-300 kms per full tank.

So from what I've read so far, changing the O2 sensor, plugs, might help. Also I didnt get what the ecu + remap + piggy back does and would it cost too much?

thanks

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

off the bat, just replace the O2 sensor (they're liek $80.00 new delivered from KUDOS), and give the AFM a clean with carby cleaner.. stock air box helps as well, and check for leaks.

nothing wrong with stock ecu if you don't plan to run many mods

If you have a PFC make sure the O2 sensor is turned on.

my tuner left mine off and was wondering why i would get 17-18L per 100km just cruising around.

It dropped down to 13L per 100 once on. hopefully get it a little lower once my tune is touched up today by a different tuner :cool:

Also I didnt get what the ecu + remap + piggy back does and would it cost too much?

If you have a number of mods it can cause the stock ecu to not be ideal for the modified setup. One thing is the ecu can go into rich and retard mode which means it adds extra fuel and takes out timing. This is more under power though but as you can see will worsen your fuel economy.

Custom tuning can also further optimise your afrs for better fuel consumption.

If you have a PFC make sure the O2 sensor is turned on.

my tuner left mine off and was wondering why i would get 17-18L per 100km just cruising around.

It dropped down to 13L per 100 once on. hopefully get it a little lower once my tune is touched up today by a different tuner :cool:

provided it works!

mines permantly disabled and I cruise at 14.7 a/f usually get up to 400km city per tank of enthusiastic driving at 1.3bar

but saying that, he runs a stock ECU

  • 2 months later...
  • 1 year later...

ah you want to know the secret to getting more Ks from a tank eh?.... I dunno guys should we tell him...

I know it an old thead but I have the secret

How do you all drive your car? It must be Full no, off, Full on, off

LOL funny

I must have the secret, here it is

Buy a hr31 two 2 door skyline. Put in it a RB25det neo in it then a rb26 gearbox and a chrome-moly flywheel, brass button clutch, bosch 040 fuel pump , adjustable fuel regulator , Apex bov, Turbosmart boost controller, Big front mount intercooler, plenum and 68mm XF body, hks cams,Oil cooler and oil filter relocation, micro tech LT-12, TO4 Turbo 69hks inlet wheel and 0.7 housing exhaust , Tial wast gate, 10l sump (for Oil), head std kit (ARP), mean std kit(ARP), commadik head gasket, gates timing balt, N1 oil pump.

and made 350rhp ish on 12psi on pits dyno and If you drive it like a normal person and you get 550ish + out of a tank. Drive like a wanker and you get about 300ish.

WIN WIN WIN ON FUEL

post-64661-0-56502200-1309183769_thumb.jpg

Just switched back to 98 after 18 months or so on E85. (Around 240rwkw)

So far on the first tank i'm up to 320km and about 1/8 of a tank left. There has been very little cruise going on. I would say 80% of the driving has been foot to the floor (very little O2 use).

Very surprised at the economy. I would love to take it for a long country drive to see what is possible but it's too much fun on boost :)

Jimmy

Hey, that's funny. I was just about to head out and buy hr31 two 2 door skyline. Put in it a RB25det neo in it then a rb26 gearbox and a chrome-moly flywheel, brass button clutch, bosch 040 fuel pump , adjustable fuel regulator , Apex bov, Turbosmart boost controller, Big front mount intercooler, plenum and 68mm XF body, hks cams,Oil cooler and oil filter relocation, micro tech LT-12, TO4 Turbo 69hks inlet wheel and 0.7 housing exhaust , Tial wast gate, 10l sump (for Oil), head std kit (ARP), mean std kit(ARP), commadik head gasket, gates timing balt, N1 oil pump.

Hoping to make 350rhp ish on 12psi on pits dyno and If you drive it like a normal person and you get 550ish + out of a tank. Drive like a wanker and you get about 300ish.

i'm a bit out of my legue here but i own a 98 nissan s2 stagea rs4

many problems with fuel economy

albeit many people here have big problems with their setups but i found the best fuel saving device was a boost guage

under vaccume the map uses the o2 sensor and leans out the engine, boost means the ecu runs a default map which is typically rich

in summary when you hear that boost whistle it sounds like this $$$$HHH

keep of boost and you are saving a bundle

Lowest i've seen out of the DE+T is 9.1L/100km. Easy highway driving, with the occasional WOT 3rd/4rd/5th coming into a 100 zone. Fresh plugs, coils, fuel filter, pump, 02 sensor, clean AFM, good oil and good maintenance helps the figure.

State of tune helps also. Plugs, coils, ECU and it's relevant sensors (o2, MAF), low fuel pressure, big tyres, poor alignment, carrying excess weight etc. etc. will all affect economy. Driving style will be a MAJOR factor over all others though...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...