Jump to content
SAU Community

Over Heating Issues

ducki

By ducki,
in Victoria

 Share

Recommended Posts

ducki Proficient

ducki

Posted
Posted

Anyone have any overheating issues with their car on these past few days? Mine never had this problem before until a few days ago, my water temp gauge rose to 2/3 of the gauge when it's usually in the middle. So I had to turn off my A/C so that the tempreture can drop back to normal.

I thought my water pump or thermostat was failing since it has never happened in the last 3 years of owning it. But this happened to a friend of mine too so I wasn't sure if it's just the heat or something wrong with my car.

If this is uncommon, then I will take the car out to the mechanic to check. The coolant in my radiator is still full so that wasn't the problem I think.

Link to comment
https://www.sau.com.au/forums/topic/210583-over-heating-issues/
Share on other sites
some_cs_student Veteran

some_cs_student

Posted
Posted (edited)

Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan gently, with a finger or similar, do not misinterpret this post to mean shove your hand straight into the fan and see what happens.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

Oh, and if you injure yourself by doing this I take no responsibility whatsoever :).

Edited by some_cs_student
GTR_STEALTH Proficient

GTR_STEALTH

Posted
Posted
Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

I prob wouldn't recommend stickin your hand in there and cranking the car.....

krzysiu Grand Master

krzysiu

Posted
Posted
Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

You can use something else, for Christs sake don't use your hand lol.

Omurru Veteran

Omurru

Posted
Posted

lol, the fans not that hard to hold still when you start the engine, the coupling just slips the same as when the engine is revving which is what keeps the fan at a fairly constant speed. I wouldn't go putting my hand in there when it's already spinning but otherwise.....

Sandeep Community Regular

Sandeep

Posted
Posted

I get my coolant changed once a year, just before summer. If you changed yours 30,000km ago, maybe try a full flush. Always best to start simple. Also get a pressure test done on the system to see if you have any leaks and if you have time pull off your front bar and clean up leaves/crap that's infront of your radiator.

If that doesn't fix it, I'd be looking at the thermostat (replace) or maybe a clogged radiator (flush/rod).

some_cs_student Veteran

some_cs_student

Posted
Posted
lol man do NOT stick your hand in ther

dumbest idea ever

I've done it on 2 different cars, and I'm fine.

I don't mean put your entire hand into the fan, I mean touch the end of the fan blade and start it, if it pulls away from you then its working.

Of course if you're stupid enough to put your entire hand in there then you've misinterpreted my advice.

Also see if its spins after you turn the engine off after its warmed up, my fan spins for a long time...

htial Grand Master

htial

Posted
Posted
Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan gently, with a finger or similar, do not misinterpret this post to mean shove your hand straight into the fan and see what happens.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

Oh, and if you injure yourself by doing this I take no responsibility whatsoever :P.

LOL... ...try sticking your dick in there... *clacka clacka clack* ;)

ducki Proficient

ducki

Posted
  • Author
Posted

LOL... Well.. you guys can try sticking your dick in there if you want.. but I used a branch and tried to put it in slowly.

It smacked my stick away so I'm assuming that my fan is still strong and it feels like its blowing hard.

Maybe I will try a flush first and see how it goes from there.

some_cs_student Veteran

some_cs_student

Posted
Posted
LOL... Well.. you guys can try sticking your dick in there if you want.. but I used a branch and tried to put it in slowly.

It smacked my stick away so I'm assuming that my fan is still strong and it feels like its blowing hard.

Maybe I will try a flush first and see how it goes from there.

Did you put the branch in while its spinning?

Or did you try putting the stick on it when you started it? If it pushes the stick out from idle when it starts moving then your fine, just don't drop the stick into the fan. lol.

Good luck with fixing the issue.

BRUNSKIGTST Proficient

BRUNSKIGTST

Posted
Posted

you gotta put in fact as well that the jap cars such as skylines werent made for Australian weather also, mechanic told me that one time and that could be one reason for it as well some one correct me if im wrong.

nickcorr Proficient

nickcorr

Posted
Posted

Japanese weather does not hit these one off hot days, but it does get very hot and humid for weeks at a time... That is why Japanese cars have much better cooling systems and air conditioners than Euro cars of the same age.... Most of us own cars that are over 10 years old, you have to expect them to get a bit upset when it gets hot...

Citroen CX aircon was so weak, that for Japanese and Australian markers, twin air conditionsers were fitted.... They added another one in the boot... It is also once of the reasons that the Commodore grew away from the Opel versions they were based on from the VL. Holden needed more space for the larger Aus spec air con units.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Whoops!
×
×
  • Create New...