Jump to content
SAU Community

Recommended Posts

Just been informed they have GT2860R-7's restrictors built in.

Guy also said a lot of people actually remove the restrictors thinking they are improving flow - apparently the shaft is actually physically supported by the internal restrictor and then go boom. Bogans and turbos don't mix. :D

Sorry to Hijack the thread, but Ive done a bit of reading on this and apparently all the GT series of Garrett's have restrictors built in.

Now I'm not sure if we should believe this, it seems as though half the people out there say to use restrictors and half the people say they are built in.

I'm about to fit a set of GT2560Rs (707160 - 9, the GT-SS equivalents) to an R32 GTR and I'm in the same boat you were, not sure whether to just bolt them up, or to put restrictors in.

The sticker on the plastic wrap the turbos come in say not to exceed 60psi which leads me to think the restrictors are not built in. Also, in the GT-SS kit (which I didn't get) they have a banjo restrictor to put in place.

Can someone with a bit a bit of knowledge please help clarify this???

I know the turbos will work without the restrictors, but will this put exessive loading on the seals and blow them out 10,000Kms down the line? or are there internal restrictors?

Sorry to Hijack the thread

No not at all - thats the kind of info I am after.

Definitely odd that it would have that warning if there was a restrictor built in. We were assured they have a restrictor - mate who picked them up said the guy showed him another turbo without a restrictor to compare.

Do not use a oil restrictor if you have one built into the turbo.

I have heard this can cause back pressure on the oil lines.

If you still want to restrict some flow......have a smaller diameter oil line made up.

IE..take your line to H.I.S. Hose and ask them to make you another line using your

connectors.

Very good Idea TiTAN, I'll call GCG on Tuesday to confirm and see if I can find out which turbos do actually have a restrictor in them, unless someone has already done this???

Looking at the oil feed hole for the GT-SS's there doesn't seem to be anything restricting there (like a mushroom looking thing that others have mentioned) it just goes into what looks like a chamber or pocket.

Is that the case with yours to paulR32gtr? or were you told that the restrictors were actually inside the turbo and not visible?

In my research, often the Garrett's come with a 1.2mm restrictor in place. However, there is a 0.8mm restrictor available from Garrett. I didn't check mine before installing, but I believe I have the 1.2mm in place.. I am also getting some oil past the turbo seals...

From what I have learned/read/asked - I would be fitting the 0.8mm restrictors from Garrett if i were you.. since they are ball bearing, you only need a good quality oil getting through there to lube them, you don't need the kind of pressure that a journal bearing requires...

I am also getting some oil past the turbo seals

Not what you want!

We are putting the turbos on tomorrow so ill compare against the stockies.

HKS GT-SS's are on the way for my car and I am going to trust their kit - guess if they are including restrictors for what are essentially a GT2860R-9 frame with all the same CHRA physical characteristics as the -7's - we should be doing something about it.

Ok, I called GCG and emailed them so I got responses from 2 different people just to be sure.

They were both very helpful and both stated that there were inbuilt restrictors so additional ones were not necessary to install on an R32 GTR in the GT2860 range.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...