Jump to content
SAU Community

Leaning Out Help.

RPR33

By RPR33,
in Engines & Forced Induction

 Share

Recommended Posts

  • 6 months later...
RPR33 Community Regular

RPR33

Posted
  • Author
Posted

nah not yet but the fuel pressure was all good when we tested it I have put in an safc2 so I can watch for knock... it just hard to look at cause it doent always happen just every now and then! or it will happen like five times then clear up?

BezerkR32 Veteran

BezerkR32

Posted
Posted

the dyno sheet would show if it was actually leaning out, otherwise you are guessing. if it does show this then the things to check have already been mentioned, otherwise get someone to look at it before you break it.

yeah I would guess a fuel pressure problem - put a gauge on it and make sure you are not short of flow up high. dying fuel pump, fuel pump wiring, blocked filter etc etc etc. some of the jap ecus are a bit leaner than we like but they should not be causing it to ping all the time
MBS206 Grand Master

MBS206

Posted
Posted

Check your TPS.

If it isn't working properly, then you will lose the throttle enrichment, hence, a lean out when you first step on it.

Also, earth the fuel pump as mentioned.

Throw some new plugs in it gapped at 0.8mm

heller44 Mentor

heller44

Posted
Posted

Clamp the return from the fuel rail, that will tell you if the pump can't keep up or the fpr is screwed.

I had the exact same symptoms, mine was a torn diaphram in the fpr so it was leaning it off all the time, as well as a fuel pump with ~10v at it when at full throttle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
×
×
  • Create New...