Jump to content
SAU Community

Recommended Posts

  • 6 months later...

nah not yet but the fuel pressure was all good when we tested it I have put in an safc2 so I can watch for knock... it just hard to look at cause it doent always happen just every now and then! or it will happen like five times then clear up?

the dyno sheet would show if it was actually leaning out, otherwise you are guessing. if it does show this then the things to check have already been mentioned, otherwise get someone to look at it before you break it.

yeah I would guess a fuel pressure problem - put a gauge on it and make sure you are not short of flow up high. dying fuel pump, fuel pump wiring, blocked filter etc etc etc. some of the jap ecus are a bit leaner than we like but they should not be causing it to ping all the time

Check your TPS.

If it isn't working properly, then you will lose the throttle enrichment, hence, a lean out when you first step on it.

Also, earth the fuel pump as mentioned.

Throw some new plugs in it gapped at 0.8mm

Clamp the return from the fuel rail, that will tell you if the pump can't keep up or the fpr is screwed.

I had the exact same symptoms, mine was a torn diaphram in the fpr so it was leaning it off all the time, as well as a fuel pump with ~10v at it when at full throttle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...