Jump to content
SAU Community

M35 Brakes

Paramour

By Paramour,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Jetwreck Grand Master

Jetwreck

Posted
Posted

Another bit of FYI on rear R32 GTR calipers.

Tried the rears on last night and although the rotor fitted the caliper has totally a different mount....bit of shame as it looked to be an easy and cheap upgrade.

  • 6 months later...
  • Replies 118
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

admS15
admS15
Blek
Blek

Finally found some time to put my brakes on. Big thanks to Scotty for fabricating the spacers - they worked a treat Removed the restrictor as directed, but the line wouldn't fit oddly.. so still h

admS15
admS15

Yes there is no need if u do that. My logic was the original m35 calipers that the factory banjos screw into don't have an olive and the lines aren't designed to be used with it in. The reality is it

Posted Images

Jetwreck Grand Master

Jetwreck

Posted
Posted

bit more of an update....forgot to add this....you will need to machine off about 2mm of the hub.....don't worry it does not affect anything.....but if you don't do it it will rub against the rotor.

  • 3 weeks later...
Bis-e Bee Mentor

Bis-e Bee

Posted
Posted
The front Brembos off 350Z, V35 Skylines will fit without any mods at all. I trial fitted them when I took off my Brembos from the Zed.

The rears im not sure 100% but my guess is that it's possible.

For a good used complete set of Brembos, you're looking at about $2500-2800 including calipers, rotors and pads. Im considering upgrading the brakes next.

Did you ever confirm that the 350z rear brakes fitted the M35?

This is on my list of upgrades once I start working on the driveline.

  • 1 year later...
BoostdR Mentor

BoostdR

Posted
Posted
bit more of an update....forgot to add this....you will need to machine off about 2mm of the hub.....don't worry it does not affect anything.....but if you don't do it it will rub against the rotor.

I'm doing this atm with R33 GTST Calipers and R32 GTR discs. The bit you machined of the hub..you are refering to the rectangle protrusion on the alloy part of the hub?

The Banjo bolt that you linished 1mm from to fit the brake line...did you do that so it seats inside the caliper and seals? Or could I just use a couple of extra copper washers to space it out?

Jetwreck Grand Master

Jetwreck

Posted
Posted
I'm doing this atm with R33 GTST Calipers and R32 GTR discs. The bit you machined of the hub..you are refering to the rectangle protrusion on the alloy part of the hub?

The Banjo bolt that you linished 1mm from to fit the brake line...did you do that so it seats inside the caliper and seals? Or could I just use a couple of extra copper washers to space it out?

Fit the rotors up....you will see where it hits......thats the area you need to remove. As far as the calliper goes I wouldn't use extra washers.....if you look inside the calliper where the banjo goes in there's a small restrictor.....you should be able to remove it by screwing a self tappers into it and pulling it out.

if you get stuck give me a buzz

cheers

Craig

0406754304

BoostdR Mentor

BoostdR

Posted
Posted
Fit the rotors up....you will see where it hits......thats the area you need to remove. As far as the calliper goes I wouldn't use extra washers.....if you look inside the calliper where the banjo goes in there's a small restrictor.....you should be able to remove it by screwing a self tappers into it and pulling it out.

if you get stuck give me a buzz

cheers

Craig

0406754304

Thanks for the quick reply Craig! Whats the go with the restrictor in the stock calipers do I use that with the R33 calipers? Or do you mean remove the restrictor from the R32/R33 Calipers?..so the Banjo seats correctly? Am I on the right track?

andy65b Veteran

andy65b

Posted
Posted
Thanks for the quick reply Craig! Whats the go with the restrictor in the stock calipers do I use that with the R33 calipers? Or do you mean remove the restrictor from the R32/R33 Calipers?..so the Banjo seats correctly? Am I on the right track?

Yes, remove the restrictor in the R32/R33 calipers so that you can screw the standard M35 banjo straight in.

When you look into the point where the banjo screws in you will see the reducer just sitting in there. Comes out the the described method.

Otherwise you need to cut off the end of your banjo that has a restricting end.

Cheers

Andy

BoostdR Mentor

BoostdR

Posted
Posted
Yes, remove the restrictor in the R32/R33 calipers so that you can screw the standard M35 banjo straight in.

When you look into the point where the banjo screws in you will see the reducer just sitting in there. Comes out the the described method.

Otherwise you need to cut off the end of your banjo that has a restricting end.

Cheers

Andy

Got it!

So no need to linish 1mm off the Banjo bolt if I get the restrictor out?

cad Collaborator

cad

Posted
Posted
Hi Jules

I do not know the size of the rotor but they are the same as the V35. The part numbers are the same. The brake pads are also the same as the V35/G35. (confirmed this with Ben).

I am looking at getting some Hawk brake pads from the US for front and rear. Just waiting to confirm the cost of rear pads.

Cheers

Andy

Hey Andy do you Know the (DB)code on the back brake pads and that of the service brake.Thanks Cad.

andy65b Veteran

andy65b

Posted
Posted
Hey Andy do you Know the (DB)code on the back brake pads and that of the service brake.Thanks Cad.

not sure what you mean by DB code? The Hawk brake code is HB30F.559 (rear)

It is unlikely you would need to replace the pads on the service brake. They can be tightened up with the wheel removed. There are instruction on how to do this in the G35 service manual.

Cheers

Andy

Bis-e Bee Mentor

Bis-e Bee

Posted
Posted

Brand new Gold Brembo's for 350z, brought 3 years ago but supposedly never fitted to a vehicle.

http://cgi.ebay.com.au/350z-Brembo-Brakes-...=item19bb209f05

Pick-up only and they are in Victoria.

andy65b Veteran

andy65b

Posted
Posted
I have R32 GTR disks and they foul on the hub arm. I would expect the R33 GTST 30mm will be ok. 32gtr is 32mm

I have the R32 GTR rotors on my M35 and they fit perfectly.

I had to remove a small raised section on the lower side of the hub arm, about 2mm thick and the size of a regular dice.

BoostdR Mentor

BoostdR

Posted
Posted
I have the R32 GTR rotors on my M35 and they fit perfectly.

I had to remove a small raised section on the lower side of the hub arm, about 2mm thick and the size of a regular dice.

Yep, looks the same here. I'm going to finish mine off tomorrow...wooho!

BoostdR Mentor

BoostdR

Posted
Posted

Ok my supposed R33 Calipers turned out to be 300zx items suited to 280mm disc's so a real pain in the butt as I now have to get a refund and source some more. They were the finned type and the legs on the calipers were considerably shorted...my guess about 16mm 296-280.

Are the legs on the R33 GTST calipers definately the same lenth as 32 gtr?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...