Jump to content
SAU Community

Recommended Posts

The ticking sound can usually be rectified with a higher viscosity (thicker) oil. Many cars of all makes with higher kms usually make a ticking sound. Subaru's are especially renowned for this. How many kms on the car and did the ticking occur once you changed the oil?

I doubt it would be your belts as the sound wouldn't go away once the engine is warmed up.

Link to comment
https://www.sau.com.au/forums/topic/213844-tick-tick-tick/#findComment-3776819
Share on other sites

The ticking sound can usually be rectified with a higher viscosity (thicker) oil. Many cars of all makes with higher kms usually make a ticking sound. Subaru's are especially renowned for this. How many kms on the car and did the ticking occur once you changed the oil?

I doubt it would be your belts as the sound wouldn't go away once the engine is warmed up.

Ah i see, i brought the car at 102,000k and now its done 106,000k. The oil that i used was motul turbo light, is there a way to reduce the noise? I like it when the motor is quiet.. An also i did not hear the tick once the oil was change it was not until weeks after

Edited by gazal
Link to comment
https://www.sau.com.au/forums/topic/213844-tick-tick-tick/#findComment-3777003
Share on other sites

Reduce the noise by changing the oil to what it was before basically. Also now that we are approaching winter your car will get even noisier on start up. This is normal. You learn to live with it, but you can reduce the noise with the right oil imo.

Don't get 0W-xx viscosity. You don't need it. Good for revving out easy but too thin and by rule of thumb will be the noisiest. If you go by the Nissan handbook, they recommend their patented 7.5W (for everything!), but that oil breaks down easy (semi synthetic). I found Motul 4100 degraded quickly too (also semi synthetic). Motul Chrono 300V was much nicer to the ears and engine. Expensive stuff though. It is a case of sticky lifters/tappets and some cars are more prone than others. In my experience it has been an oil thing and has a direct correlation with the outside temperature as you will notice.

This is just from my experience and of various mechanics recommendation.

Edited by HotPlates
Link to comment
https://www.sau.com.au/forums/topic/213844-tick-tick-tick/#findComment-3777100
Share on other sites

Cool, thanks for the feedback guys.. So what is it? the oil or the gasket? i dont know much about cars and if there's something wrong i'll take it to a workshop. I rather find out what could be wrong with it so that if i do take it to a workshop i don't come out with a new car..haha

Link to comment
https://www.sau.com.au/forums/topic/213844-tick-tick-tick/#findComment-3777432
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...