Jump to content
SAU Community

Recommended Posts

that is way to high, it should read 4 and then drop to bar below that once warm, make sure u have the right amount of oil

checked the oil. its slighty above the max mark but 1-2mm.

btw im using full synthetic oil.. i think 60/10.. (Think)

could that be the problem?

Link to comment
https://www.sau.com.au/forums/topic/214069-oil-pressure/#findComment-3779969
Share on other sites

That sounds like the oil is too thick which is making the pressure very high when it is cold.

Skylines like oil in the 10-40 or 7.5-40 range only and synthetic if you can afford it. The best is Motul Chrono 10-40 but it is nearly $100 for 4 litres.

Link to comment
https://www.sau.com.au/forums/topic/214069-oil-pressure/#findComment-3781188
Share on other sites

  • 1 month later...

can anyone confirm with me the dodgy oil pressure gauge on my S2 r33? I have a fresh built motor with the lot internaly but about half an hour nto my first outing at the track the indicators went funny and the oil pressure now sits on a big scary 0 at idle but isnt making any bad sounds (knocking as it should if the pressure was correct).

When I rev it it only gets to just above the first bar on the gauge but all was working perfect before the indicators went oh and no fuse's are blown. also the oil pump is a tomei item for a RB26 to fit my 26 crank. waiting for my oil filter spacer to come so I can fit my mechanical oil pressure gauge.

any one have a similar problem with the R33 S2 oil pressure gauge?

Link to comment
https://www.sau.com.au/forums/topic/214069-oil-pressure/#findComment-3899329
Share on other sites

erm ...

Cold start.. esp winter mornings... its normal for ur pressure to reach around 7 for the frist few mintues of driving....

After its warmed it will drop down ...

Idle around 2.

And when u drive should b around 3.5.

I have the offical figures in my room... i printed out the service manual.

Edited by br3ndan
Link to comment
https://www.sau.com.au/forums/topic/214069-oil-pressure/#findComment-3899767
Share on other sites

thanks man but this was after some full blooded runs at mallala so yeah i think it might be a dodgy stock gauge as the indicators went as well so yet to put the mechanical gauge on but if you can give some psi readings that would be great, so when i finaly get back to my car to check it out i know what im lookin for :D

Link to comment
https://www.sau.com.au/forums/topic/214069-oil-pressure/#findComment-3909484
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...