Jump to content
SAU Community

Recommended Posts

I drove from Bathurst to Sydney this morning, and after a while I started to notice (hear and feel) a vibration resonating from what I'm pretty sure is the gearbox area. I tried accelerating in a few different gears past 80km/h and the shudder was the same for all, so I determined it isn't a gearbox problem. the engine still revs fine up to 7000rpm so it's not an engine problem. the shudders aren't coming through the steering wheel as such, more the entire car is shuddering, so it's not a steering alignment/balance problem. It picks up a resonance of around 1-2Hz as I'm driving over 80km/h, but it comes and goes, usually for about half an hour at a time. The vibrations are constant however.

My theory is either a Uni-joint on the tail shaft, or a bearing somewhere in the gearbox/tailshaft region. I'm not an expert on the mechanics down there so it's just speculation.

My question now is has anyone experienced a uni-joint or tail shaft problem before? this is a first for me as neither of my previous cars have had the problem. If I'm right and it's a uni-joint, how hard/expensive are they to replace? I'm trying to sell the car, I don't need an expensive repair job right now.

If anyone has some guidance for me let me know, otherwise i'll have to see a transmission mechanic to help me out.

Cheers,

Leshy

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

It does sound like a uni joint. :blink:

I've had one fail ever so slightly and it is definitely felt in the body of the car. Fixing them is simple enough if you wanna give it a go yourself.

Remove the circlip and use a flat head screw driver and hammer to tap them out. A suitable mechanic should be able to replace them cheap enough.

Also, if your tailshaft is out of balance, this will cause the problem also. But the weights to balance it are usually welded on, so its rare.

Edited by RubyRS4
Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3783725
Share on other sites

Not good dude! It might be a uni, but in my experience if the uni is failing there is usually a tapping or knocking sound associated with the vibration due to the bearing surfaces in the uni constantly coming in and out of contact with each other. I know tailshaft balance problems are rare, but I would be looking closely at the rear tailshaft anyway to make sure there are no shiny patches where weights may have dropped off.

Yours is a manual, isn't it? How was the clutch surface of your flywheel when it was installed?, but you will know if this is the problem because the clutch will start to slip.

Also have a close look at your wheels (esp the front ones) to make sure there is no balancing weights that have gone south.

Other than that, all I can think of is the dreaded ATESSA system problems (maybe chain drive to the transfer case?)

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3783834
Share on other sites

yeah i don't think it's out of balance, hopefully just a uni joint. are they skyline / stagea specific, or just a generic uni joint off the shelf? I'll have a look when I get home on the weekend, see if there's much movement in the joints.

I've already blown one transfer case apart, i don't want to do it again. it's making very differnet noises to the time my transfer case kicked the bucket, so that's why i didn't think that initially. I had the flywheel machined flat when I had it all installed. The vibrations are intermitted, so perhaps it's only just starting to fail? theres a lot of vibration in the gearstick too.

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3783838
Share on other sites

Are you sure there is no noise? Cause when the uni in my front drive shaft went, the clacking noise drove me nearly batshit crazy.

The uni joint can fail ever so slightly that the tailshaft is slightly out of alignment horizontally, making it out of balance. Whereby you feel the vibrations, but no noise might be assoicated with it as the joint spins up with centrifigal forces. A bit like sitting in the Gravitron!

:blink:

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3783887
Share on other sites

yeah well it gets worse with speed rather than RPM, which ruled out the clutch. I know I need new front tyres and a wheel alignment/balance, but it shouldn't be vibrating the whole car. also the noise is coming from the gearstick hole. i'm glad i didn't seal the hole completely, else I might not have heard it at all.

I'd hate to go batshit crazy, i'll fix it asap!

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3783943
Share on other sites

Well my problem answered itself. I'm currently stuck on the side of the M4 near the cumberland highway with a front driveshaft hanging out of my car. cruising along at 90k's something suddenly went BANG then i lost my clutch and the engine died. the driveshaft was hanging off the front of the car like a rag doll.... this is the 2nd time my gearbox has kerploded on me, i don't know what i'm doing wrong, i had professional gearbox mechanics install it after it broke the first time.

anywho, i'll just become a resident of the M4 for the next hour or so until NRMA comes to pick me up I guess.... doh

it has to happen when I'm trying to sell the car doesn't it.

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785403
Share on other sites

sh1t dude ! bad news ! I was hoping to get on here and say" check the tyres for bubbles " and you would be like ZOMG thats it - and I would be like - huzzah - hooray for boobies- and that sort of cary on .

maybe your gearbox / transfer case mounts are stuffed?

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785426
Share on other sites

Well my problem answered itself. I'm currently stuck on the side of the M4 near the cumberland highway with a front driveshaft hanging out of my car. cruising along at 90k's something suddenly went BANG then i lost my clutch and the engine died. the driveshaft was hanging off the front of the car like a rag doll.... this is the 2nd time my gearbox has kerploded on me, i don't know what i'm doing wrong, i had professional gearbox mechanics install it after it broke the first time.

anywho, i'll just become a resident of the M4 for the next hour or so until NRMA comes to pick me up I guess.... doh

it has to happen when I'm trying to sell the car doesn't it.

Damn, that sucks :( but at least you've found the problem :( big :thumbsup: that can be the worst part, not being able to find what the problem is...

lol you've got no car, you're stuck on the side of the M4, and you're still posting? :laugh:

Edited by DaveB
Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785429
Share on other sites

well when i initially put my gearbox in, the transfer case destroyed itself within a month. I got the whole thing replaced properly and now this happens after 6 months. I'll be talking to the workshop in question about a warranty on this, because there's no way I'm that unlucky to buy 2 lemon transfer cases

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785433
Share on other sites

Oh man that sucks the big one! :thumbsup:

If its your driveshaft that blew, how recently was your gearbox fixed the first time? Try hitting up the mechanics for a repair. Was it bearing failure? Check the docket/invoice from you previous work to see what was involved. It might be covered.

Sorry, the only assistance I can give seeing I'm in Adelaide and you're on the side of the M4.

:laugh:

Added: can you get pics of the damage/break? Post 'em up

Edited by RubyRS4
Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785434
Share on other sites

Damn, that sucks :( but at least you've found the problem :( big :thumbsup: that can be the worst part, not being able to find what the problem is...

lol you've got no car, you're stuck on the side of the M4, and you're still posting? :laugh:

Wireless Baby! I've got my work laptop with me and a NextG card

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785443
Share on other sites

Um...maybe because the front shaft has taken out your clutch actuator :thumbsup:

When mine went, the uni had punched the bearing retainer almost al the way through, I was about 5km of driving away from what happened to you....

Link to comment
https://www.sau.com.au/forums/topic/214256-good-vibrations/#findComment-3785579
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...