Jump to content
SAU Community

Recommended Posts

As of today, Journalists will be wiriting up the new FG line up..

I got these figures from drive.com.au for the xr6t

0-100km/h: 5.1 seconds

0-400m: 13.4 seconds

Top speed after 400m: 172km/h

From the article:

For the record, the air-conditioning was on. There were no stunts, no tricks, we just squeezed the accelerator. It did it like it was brushing its teeth.

This not only makes the latest Falcon XR6 Turbo the fastest Falcon to date, it also shoots it to the top of the leader board in Australian performance cars. It’s faster than both the Holden V8s and its own big brother, the Falcon XR8 (which stopped the clocks at a comparatively slow 6.3 seconds).

Since the FPV F6 is expected to come with a 310kw figure, expect the 0-100 acceleration time be in 4 seconds and quarter mile in on mid to high 12 seconds

http://www.drive.com.au/Editorial/ArticleD...;vf=12&pg=2

Edited by Barbarian
  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Is it just me or does every photo of the new Falcon look like it has a really skinny trackwidth?

GT-R times will be much quicker than the Falcon.

I've seen a couple fg xr's on the road and they appear some what smaller than BA/BF's.. also from what I have read, tracks for both front and rear were widened.

Ford Aus promises this car to be the best handling Aussie built car to date.

hell yeah

bring on the fpv f6

it was always said that the BA/BF were the best looking fords ever built - i think they have surpassed that with the FG

very very stylish....

(i dont think there is a common exterior panel between the BF and FG)

i wonder :thumbsup: if it will have shitty ill fitting plastic bits in it and other things that fall off or break :laugh:

parents have a territory AWD ghia and nothings fallen off yet (and its 2 yrs old...)

Not bad. You'd think theyd release photos that aren't in a shit colour...

Car companies always take the most eye-catching colour since it photographs the best.

From Nissan's perspective, look at the horrible Sunset LeMans orange (and the new solar orange) that most of the 350Zs in the promo posters etc are shown in. Really vibrant when printed, and it comes off the background well, but in the metal its really tacky.

The old BA/BF performance Fords had their promo / press cars in that sickly green, too. Great to shoot, bad to look at.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...