Jump to content
SAU Community

Recommended Posts

hey all i just had my ssqv installed. backfiring heaps lately.

i had my safc tune b4 the ssqv was installed.

do i need to retune it or it makes no diff??

n one more question.

if i have a recirculation adapter for my ssqv, will there be any affect if i change between atmo n plumb back once a while.

thanks!

ps: if there was a topic similar, could u just post the link for me! =p

many thanks again!

Link to comment
https://www.sau.com.au/forums/topic/214423-ssqv-installed-after-safc-tune/
Share on other sites

BOVs won't effect performance or anything.. unless ur running high boost and the stock one's leaking

you dont have to retune your car

you can use dec air so it doesnt stall at the lights, but you have to be careful because that can effect the cold start too... it happened to me

check your cold start airflow using the safc and set it at that.. but even with that the car still stalls...

or just change your driving style, don't drop to neutral and roll to the lights, only drop to neutral just before the car's about to come to a stop, then this way it won't stall

/\ -- for post above..stalling issues are common with ATMOS bov's due to the loss of air quickly when slowing down eg to lights when in neutral etc or i have even heard of it when people drive slow between gears. it tends to happen under load.

" or just change your driving style, don't drop to neutral and roll to the lights, only drop to neutral just before the car's about to come to a stop, then this way it won't stall " i run an ATMOS HKS ssq bov n have never had this problem, it due to the tention of the bov.

there are stalling issues after installing the ssqv.

Only thing that is different is the backfire and the wanker noise :D

thanks guys! :O

sorry guys....

dammit. gotta proof read b4 posting....

i do not have stalling issues.

just backfires and the wanker noise. LOL

i am so sorry for confusing u all.

SORRY!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...