Jump to content
SAU Community

Recommended Posts

Make: 96' Nissan Skyline GTS25T

Milage: 85,000km

Transmission: 5 speed

Colour: Grey Silver

Location: Sydney Parramatta

Complied? Yes

RWC supplied? Yes

Currently registered? Till Feb 09

Price: $16,000neg

Contact: Via Pm or 0410 687 984

Comments / Modifications:

This has all been done by Matt @ BEL...........

**Tube & Fin Front Mount Intercooler

**Garrett 3076 only done 2000km

**Ems 8860 ( this is one best Aftermarket computer going around Now)

**Os Giken Twin Plate clutch

**Greddy profec B sepc II

**Tial Wastegate 38mm

**Nismo 740cc injectors

**Walbro Fuel Pump

**Sard Fuel Reg

**D1 spec Catch can

**K&N pod with custom box

**Liverpool exhaust Custom 3" mendrel bend exhaust.

**Spitfire Coils

post-42470-1208762329_thumb.jpgpost-42470-1208762359_thumb.jpg

post-42470-1208762401_thumb.jpgpost-42470-1208762451_thumb.jpg

This car is a dream to drive. Standard internals Running still at 157comp on all.

9psi = 220rwkw

14psi = 250rwkw

17psi = 271rwkw

Link to comment
https://www.sau.com.au/forums/topic/215787-96-nissan-skyline-gts25t-271rwkw/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Well hopefully some will be intrested in 16

Had no luck...................

I am in no rush man ...... if it goes then it goes

  • 4 weeks later...

16k!!

Give it some time and the right person will come along!! Just gotta be patient.

But then again 33 market is flooded and the prices are dropping like crazy :)

Edited by siddr20

I agree with siddr20, even if you wanted 13 thousand you'd still be somewhat hard pressed, but when people see a modified 12 year old car then it's going to be hard, is the car on carsales.com?

nah what i meant was.. keep it at 16k.. dont bring it down further!!

its such a tasetful car with some really nice mods :teehee: someone will appriceate it and buy it!!

gdluck

do you pay more for the plates each year? what gauges are mounted on the b-pillar? did the ems plug in? does it need any type of engineer cert for anything / could you be defected for anything? bov?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...