Jump to content
SAU Community

Recommended Posts

Just wondering how normal this might be (I'm pretty sure it aint...). I picked up my car this week, 2000 Skyline R34 GTV (N/A) coupe. The steering holds to the left mostly so I went to get the wheels aligned. Was told it was 4mm out at the front, 2mm at the back. Was told camber and everything is set up 'right'. The car still holds to the left, I went back and told them. They drove it again and eventually agreed so changed the tyres. We went for another quick drive and he tells me it's holding to the right now so it must be the tyres.

I drive off and realise it's still holding to the left. :P The steering seems to very easily change direction when driving depending on the angle of the road. Even on seemingly flat roads it will veer and happens with / without braking so probably not due to the discs. So my question is how normal is this in a Skyline ? I will go to centerline suspension and try to sort it out when I have some spare time but alas that won't be for a while so just hoping to get some ideas in the meanwhile

:D .

Pretty sure its just alignment. If you can get more castor added that will help, or maybe a bit of toe. If you got a printout of the settings post it up so the gurus can take a look, and give you real answers instead of my guesses.

a print out of the alignment settings (after not before) will reveal all :blush: Apart from alignment settings I once had a trouble with badly uneven tyre wear which casued a pull. but start with the alignment - what were the results?

These guys didn't give me a printout :blush: It was my local Bridgestone. After driving my other car and comparing I may have been overanalysing this. BTW my suspension is stock (as with every other aspect of the car).

If they dont give you a print-out, they haven't done it properly!!!

I had a Firestone dealer in Deception Bay Qld do the same thing, perform an alignment on my car because it was chewing the inner corners of the tires off premeturely.

I had new tires and an alignment done at the same time, drove home from Brisbane to Sydney, and found that I had chews excess wear on the inner edges AGAIN :blush:

Anyway, took it to a guy in Sydney who I trust 100%, got the alignment done, got a print out of the before and after settings, was told to take the sheet back to the previous aligner and laught at them, and the tires worn evenly ever since.

Sometimes you will get people that cant align wheels for their life, it doesn't take much to "tell" someone you can align their wheels, but unless they are willing to provide a printout of the settings, either they haven't done it, or haven't done it properly, and either way, I wouldn't go back there.

B.

  • 3 weeks later...

Diver, find someone else to align the wheels.

It's not uncommon for import owners to shuffle between 4 or 5 places until they get the perfect alignment, because imports are not commonly known cars, and some places just assume it will have similar figures to another car.

As mentioned before, I had a Soarer aligned in Firestone Deception Bay Brisbane, no print out, but there was marks on the bolts, so they had changed settings under the car, and done something.

It originally went in with an issue of scrubbing the insides of the tires, and pulling slightly to the left, this was before and after I swapped wheels and tires, and had just gone and put 95% worn 2nd hand 17" tires on the beast.

Anyway, got the car back, it drove straight, but as it was scrubbing insides, this was more my concern.

Anyway, drove home to Sydney, did about 15,000kms of other trips (I am a high milage driver) and the insides of the 95% 17" tires where stuffed AGAIN.

Took it to my normal guy, 4 new Pirelli Tires, and an alignment, and he printed off the before and afters of the alignment, and there was a HUGE difference in the figures.

I am now up for tires on those 17" wheels again, but this time I have done 62,890kms on the wheels, all 4 tires ahve worn the same amount all the way around, AND all 4 tires have worn perfectly even from the outside edge, to the inside edge.

These wheels are now on my Skyline GTR as well, and the tires will be changed in a few weeks (there is still 1.3mm of tread left).

I will be going back to the same guy for the next tire and wheel alignment, because he actually knows what he's doing.

B.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...