Jump to content
SAU Community

Rb25det 5 Speed Gearbox X 2

Guilt-Toy
 Share

Recommended Posts

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted (edited)

Item:RB25 Gearbox's, one has a full conversion kit one is a box on its own

Age:no idea

Condition:not sure on the condition, they were fine before the cars crashed

Price:$1200 for the box on its own, and $1800 for the whole manual conversion kit (has a good clutch on it)

To Fit:r33 gtst or whatever you like (What car)

Location:Newcastle

Contact:me by PM

Comments:

I am wrecking a whole black r33 gtst, has a decent sized turbo on it and injectors and some 17" SSR wheels (look like jap wheels) $600 for the wheels with legal tyres

Haltech e11v2 computer, comes complete with plug and play harness for R33 GTST and map sensor and air temp sensor, am looking for $1700 for the computer ONO.

I am not pulling the car appart to list parts individually, but you are more then welcome to request parts in this thread. no front end parts are available as it was hit very very hard. pics comming soon.

Can sell the turbo and dump and oil / water lines & injectors & computer & fuel pump all together if someone wants a power upgrade which made 300rwkw on 14psi

Edited by Guilt-Toy
Link to comment
https://www.sau.com.au/forums/topic/217108-rb25det-5-speed-gearbox-x-2/
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
  • Author
Posted

the turbo looks like its a VG30 rear with a .70 comp cover and massive wheel in the front.

injectors are red, might be nismo 740's

Do you know what the turbo and injectors are?
Guilt-Toy Grand Master

Guilt-Toy

Posted
  • Author
Posted (edited)

added pics of the wheels and other bits

Blitz BOV $200

leaving the wheels at good same price, even though they are good quality jap wheels they could do with a paint job, some gutter scraping on it but it only chipped the paint.

post-1240-1209598796_thumb.jpg

post-1240-1209598831_thumb.jpg

post-1240-1209598868_thumb.jpg

post-1240-1209598889_thumb.jpg

post-1240-1209599012_thumb.jpg

Edited by Guilt-Toy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...