Jump to content
SAU Community

Recommended Posts

Hey guys i recently stuck my car in to get tuned, they reached about 9 psi and started to have issues with knockin.. etc scratched their heads for a while and worked out that the air fuel ratio was changing dramatically between runs without them changing any settings.. between high 10:1's to low 12:1's on boost

my mods are intank walbro fuel pump, power fc, fmic, full exhaust n a blitz ebc.. ive tried earthing the fuel pumps earth to the battery and the results remained much the same

any ideas would be greatly appreciated

Cheers

Jarrod

Link to comment
https://www.sau.com.au/forums/topic/217183-varying-afrs-on-dyno/
Share on other sites

yeh i would of liked them to have done this but i wasnt there as i was at work, had a mate take it up.. the ppl that dynod it turned out to be completely useless coz they could of chekd the coilpaks n pressures while it was on a dyno, n i don't want to have to send it to another place n another dyno just to get the problem resolved, just would like to know some of the most likely causes.. the earth wire on the in tank fuel pump is exposed n a little corroded.. that couldnt be causing the issue could it?!!

located in perth guilt-toy, thanks for the pointers guys ill probally replace the fpr first and over the fuel pump becuz its the cheaper one to replace... are they any fpr's that are direct replacement that dont need adjusting? is the sard one any good?

located in perth guilt-toy, thanks for the pointers guys ill probally replace the fpr first and over the fuel pump becuz its the cheaper one to replace... are they any fpr's that are direct replacement that dont need adjusting? is the sard one any good?

It goes in this order

Test

If broken

Replace

Dont just go replacing random parts dude, test them, find the problem and then fix it the first time rather than bringing more problems into the equation

you said it was doing it under load, you must therefore test it in the same fashion

You 'can' do it on the street, but you wont be able to see the AFR's without a wideband and a proper read out.

Take it back to the dyno place and demand they do a semi-reasonable job. They did a half assed one last time

yeh i got a wideband with a datalogit.. i rang up the shop this morning n askd why they didnt test the fuel pressure n they claimed coz they were borrowin the dyno they didnt have their tools with them to do it ... so now i have the dilemma of sendin it to another shop with a dyno to diagnose.. why im tryin to just fix it myself coz all the shops in perth seem to be useless..

anyone know if a 180sx fuel pump will work in a r33 gts-t?!? i borrowed a girl my stock one because she thought her one was broken n claimed several ppl said it was the fuel pump so after we installed the fuel pump for her we found out she had a kink in her fuel line, when and got home, i tested her fuel pump n it still worked.. id swap them back sooner but shes in bali for a while .. so would it be fine to test a 180sx one in the skyline for a run to see if the afr's hold more steady on the wideband

ahh think i might just buy the new fuel pump.. standard wiring isnt the best anyway the earth wire is exposed and a little corroded so ill buy a full replacement one... so tomei or nismo?!! i know you probally can't go wrong with either but what one would allow for more hp?

Cheers for all the advice aswell guys

  • 2 weeks later...

hey guys sorry to bring up an old thread but im still having afr troubles, i bought a new tomei fuel pump to replace the walbro, no change still playing up... bought a sard adjustable fuel pressure regulator.. same results...varies between 12 n 14.4 around the 6psi mark... and varies between 9.5 and 12.2 around the 10 psi mark... im measuring the results with a innovative motorsports lc-1 hooked upto a lap top... has anyone else got any other ideas that could cause the results to vary so much

Cheers

Jarrod

Edited by jarrod83

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...