Jump to content
SAU Community

Recommended Posts

  NYTSKY said:
Hi all,

Im picking up a series 1 RB30 block,does the series 1 have oil squirters or is it the series 2 that has them? (piston)

No RB30's that I have ever seen have block mounted oil squirters, that's Commodore RB30E, Commodore RB30ET, Nissan Skyline RB30, Series 1 or Series 2. They all have the basic 1980's style conrod oil holes.

  Quote
Is the series 1 block a good block to use in a 25/30 combo?

Any good block is a good block to use.

Cheers

Gary

there is another block that can be used, but it does require a fair ammount of work to the block to be able to adopt a twin cam head,its do-able and it weighs about 30ks heavier than a standard rb30 block, the cylinder walls are a shitload thicker than a conventional rb30 block and will last well over the 1000 wheel hp mark.....

this particular block comes with piston oil squiters.

2jz is in trouble now....

  den001 said:
there is another block that can be used, but it does require a fair ammount of work to the block to be able to adopt a twin cam head,its do-able and it weighs about 30ks heavier than a standard rb30 block, the cylinder walls are a shitload thicker than a conventional rb30 block and will last well over the 1000 wheel hp mark.....

this particular block comes with piston oil squiters.

2jz is in trouble now....

And this mystery block is......?

  NYTSKY said:
And this mystery block is......?

My guess is RD28T, 2.8 litre (2825cc) turbo-charged diesel 6-cyl, bore: 85mm, stroke: 83mm.

I looked at it about 6 years ago, there is a lot of work required to fit the RB30 crank (86 mm stroke) and conrods. Plus the cylinder head studs don't line up with an RB25/26 head. The water jacket needs modifying and the oil feed will need some external help.

Cheers

Gary

thats teh 1, deisel, runs somthing like 22:1 compression. found in the nissan partol 92 models.... there is about 4 to 5 grand in block modification, there is a rear water jacket that needs to be welded up, and also 3 oil returns dont line up, need to modify the head aswell to compensate

Its too hard to fit oil jets to a RB30, I know of one shop that used five blocks before he found one that could take all size jets. The sand cast blocks of the RB30 was just to inconsistant with its core shift during casting for consistant fitting of the jets

  den001 said:
alrite bud, you know everything

dont take it to heart mate, just saying, there are plenty of high powered RB30's out there, and its alot of work to get the RD28 block going with the 3 litre innards. i havent really heard of RB30 blocks letting go, bar those extreme cases of problems (tuning, oil contro, whatever), or extreme horsepower, but even with the latter there isnt an abudance of supporting evidence, not that i've seen anyway

  • 2 weeks later...

A friend of mine has a 25/30 setup.

Spec's are as follows,

STD Series 2 Block

STD rods and pistons (Motor has not been apart since god know's when)

RB25 head

STD Head ports

STD intake manifold

set of small cams

STD rb25 EX manifold

GT3540 0.86 rear

Haltech e11v2

044 pump

STD R33 box

H/D clutch

made 480HP on 20PSI pump fuel

Daily drive for the last 2 years @ 20psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • E10 is pretty tightly regulated in percentage. Too much and engines can't adapt. Every incentive is against them to have too little ethanol though. The more ethanol the higher the octane.
    • Yeah i have R34 with factory small box and now RB25DET NEO swapoed and iam planning to upgrade to big box.  So i would be good as long as i do not change diff? 
    • Based off what you’ve said here, I think I’ve figured out a good bit of what I’ve done wrong -  So on the line going from the PCV valve to carbon canister, there’s a T joint that is pretty much right next to that lower port - I hadn’t noticed that the hose in the diagram was curved to attach onto the carb, so I was putting that line for the lower port onto the PCV line / carbon canister line instead. I’m going to have a flick through the manual again tomorrow and should hopefully find a diagram that’ll show me where that T joint should be connected to. Timing also 100% needs to be sorted out as well, should be able to tackle that tomorrow as well. Definitely feel like I should be on the right track now though. 
    • The screw is for idle (pilot circuit) mixture adjustment. Else, I'm confused ~ the diagram shows 2 carby ports, and the intake manifold port, but you're suggesting the "2nd port on the back of the carb that isn’t mentioned in the diagrams" ...yet, both carby ports are shown...que?... ...in any event, that port should be connected, but if not (like it is now), it's unlikely to cause a backfire out the carby (it would introduce false air and give you a fast/lean idle) ...sounds more like timing issues/spark plug wire routing responsible for the backfiring.    
×
×
  • Create New...