Jump to content
SAU Community

Recommended Posts

The 60 is when the oil is cold and you want your oil to be think on cold start to protect the engine from wear. is more the smaller number that is inportant because that is the thickness when hot which is what your engine spends most of it's time being. If you look at what nissan suggests for our climate and they recomend 10W-30/40/50. For 5W-?? the climate they suggest for this is around 10 degree max. If i was on my computer i could post the chart up from the manual, i can do it later if people are interested.

Edited by D_stirls
The 60 is when the oil is cold and you want your oil to be think on cold start to protect the engine from wear. is more the smaller number that is inportant because that is the thickness when hot which is what your engine spends most of it's time being. If you look at what nissan suggests for our climate and they recomend 10W-30/40/50. For 5W-?? the climate they suggest for this is around 10 degree max. If i was on my computer i could post the chart up from the manual, i can do it later if people are interested.

I think you have that totally backwards.

The lower number is how the oil acts when cold (in the case of a 10-60 weight oil the oil acts as if it is a 10 weight oil (thin) when cold.

The higher number "60" reacts the same as a 60 weight oil (thick) when hot.

All engine oils get thinner when hot, so the oil will not be physically thicker when hot.

When cold you need a light oil to move from the sump to all the parts that need the oil to lubricate. In a freezing temperature climate ie Canberra in Winter 5w engine oils assist in starting the car and limiting engine wear.

Most of the engine wear on a normal car occurs at startup where there is limited lubrication.

Better re-read that chart.

I think you have that totally backwards.

The lower number is how the oil acts when cold (in the case of a 10-60 weight oil the oil acts as if it is a 10 weight oil (thin) when cold.

The higher number "60" reacts the same as a 60 weight oil (thick) when hot.

All engine oils get thinner when hot, so the oil will not be physically thicker when hot.

When cold you need a light oil to move from the sump to all the parts that need the oil to lubricate. In a freezing temperature climate ie Canberra in Winter 5w engine oils assist in starting the car and limiting engine wear.

Most of the engine wear on a normal car occurs at startup where there is limited lubrication.

Better re-read that chart.

Yep sorry i have the numbers around the wrong way;

But here's the chart;

post-27020-1209911315_thumb.jpg

The 10 or 10W is not a viscosity its a cold pouring index . So 20w50 is not 20 weight oil when its cold .

Synthetic oil is supposed to be quite "thin" when it's cold like very cold and this would be a huge advantage at start up .

Plenty of people like the Edge 10w60 but if the 60 number scares you Mobil do a synthetic 15w50 from memory .

If I was pushing a turbo engine hard and for any length of time I'd use the 10w60 too .

A .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Did you take the MX5 for a Blat around the Track at all?
    • LOL, "they said it might be slippery"..... 30 seconds in your off, 60 seconds in white twin backs into the corner That new track looks good, and the Datsun was chopping cars quite nicely     
    • I'll get one of these also just for giggles
    • I bought 6 new spark plugs to compare readings. They will be here tomorrow and ill see if meter is far off if it all. I know one is at least reading 0 so its best replace all anyway if one is bad, from experience. I still have to test the harness just to be sure its not a double issue and I waste my time haha-the old plugs are iridium I always thought those lasted more than 50,000 km.
    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
×
×
  • Create New...