Jump to content
SAU Community

Recommended Posts

Wrecking R32 GTST. Most parts availiable besides engine and box. Not a lot of good panels.

* Manual pedals, tailshaft, master cylinder, etc

* All interior parts

* Brakes

* Diff

* Boot lid

* Tail lights

* Stock wheels but can't guarentee condition

* Drivers side door and rear 1/4 windows

* 3" turbo back exhaust

Any other parts just ask

Feel free to make an offer

Located in Tassie

Ph. 0409 958 227

Link to comment
https://www.sau.com.au/forums/topic/218065-wrecking-r32-gtst-tas/
Share on other sites

Finally got a list of parts still avaliable

*Tail lights in mint condition - $80

*Pedals, tailshaft, gearbox crossmember, etc (basically everything fora 5 speed conversion minus box, clutch and flywheel) - $200

*Radiator - $50

*Turbo - cat 3" exhaust (tig welded stainless with screamer pipe for internal gate and only 3 weeks old) - $200

*Cat back 3" exhaust (has a few small dents and has had a small section of straight replaced as it was a bit squashed) - $200

*Instrument cluster - $70

*Console with lid - $25

*Drivers door window - $50

*Factory looking fitted floor mats - $20

*Drivers side chrome window strip - $20

*Power steering pump, reservoir and all lines - $40

*Complete aircon set up - $30

*Heater box - $20

*Drivers side power window switch - $30

*Wiper motor - $10

*Rear wiper motor and arm - $10

*All seats (trim in very good condition) - $250

*Boot carpet and spare tyre cover board - $20

*Brake booster - $20

*Engine mounts and crossmember (ideal for Silvia/180SX RB conversion) - $50

*Glovebox and all dash parts - $30

*Diff (minus brakes and cant guarentee driveshafts until its out of the car) - $150

*Bootlid with shaved spoiler holes (gunmetal grey in colour) - $120

Edited by PSI086

*Turbo - cat 3" exhaust (tig welded stainless with screamer pipe for internal gate and only 3 weeks old) - $200

*Cat back 3" exhaust (has a few small dents and has had a small section of straight replaced as it was a bit squashed) - $200

pics of these two items,preferably of the cat-back still atatched to car

and price of delivery to NSW 2164

cheers

P.S you got an ashtray?

  • 4 months later...

Still got a few bits and pieces left over which I'd like to clear out of the shed

*Console with lid - $25

*Drivers side chrome window strip - $20

*Hicas power steering pump and reservoir - $20

*Wiper motor - $10

*Rear wiper motor and arm - $10

*Front seats in very good condition (drivers side back section had a slight twist in it but has been repaired) - $100

*Glovebox - $30

*Various dash and interior parts - $offers

*Bootlid with shaved spoiler holes (gunmetal grey in colour) - $100

*Interior lights - $10ea

*Power window assemblies - $20ea

*Door handles - $10pr

*Instrument cluster surround - $10

*Space saver spare and tyre (never fitted to car) - $50

PM me or Phone 0409 958 227 as I don't get on here much

Edited by PSI086

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...