Jump to content
SAU Community

Recommended Posts

QUOTE(yellow submarine @ 17 May 2008, 07:29 AM)

What about a HKS GT2535? Do they have good response and power?

It is a responsive turbo but you will probably be hitting 250-270 rwkws? depending on mods.

I have the HKS GT2535 on an RB25DET makin 240rwkw pretty responsive turbo very happy with it. In the process of getin injectors, z32 afm and fpr then uppin the boost to 17 psi from 15psi hopefully pull abit more power out of it. Good turbo if ur only chasin the 240rwkw mark fun and responsive :) Also it fits under the standard heat shield very nicely :)

Edited by iLEC

Yeah a bit dumb I know, I saw that post again after posting my comment then re-reading the thread. Oh well.

I have narrowed it down to the GT2535 and the GTRS. Does anyone know the difference and response of these 2? If they are similar I will just go the cheaper path, though I am leaning toward the GTRS.

On the R34GTT we ran a GCG ball bearing high flow and it make 270 rwkw with very good response. In fact, as I have posted many times, it made more power everywhwere, from idle to redline, than it did when it was standard. It was so good for what we do, I have just fitted another one (R34GTT high flow) to the rebuilt RB25.5DET in the R33GTST.

Cheers

Gary

Yeah Sydneykid, what boost and what supporting mods? I've got;

  • Blitz turbo back exhaust
  • Blitz front mount
  • Nismo oil cooler
  • Power FC

And I am getting;

  • 550cc injectors
  • Bosch in tank fuel pump.

Would I be looking at a similar power figure with a good tune? Because if I am, then i'll just go a GCG hi-flow.

On the R34GTT we ran a GCG ball bearing high flow and it make 270 rwkw with very good response. In fact, as I have posted many times, it made more power everywhwere, from idle to redline, than it did when it was standard. It was so good for what we do, I have just fitted another one (R34GTT high flow) to the rebuilt RB25.5DET in the R33GTST.

Cheers

Gary

thats what I'm running with the same result. response is great...power is good and runs a good 116MPH down the strip...which is good for a low 12 if u can launch properly.

You'll be happy with either. Both GTRS and a high flow are straight bolt on. The GTRS will need the oil lines replaced with the supplied ones and the high flow won't.

In the end regardless of the difference in reponse/power I doubt you'll notice it.

You'll be happy either way I recon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...