Jump to content
SAU Community

Recommended Posts

Hi Guys,

I know this type of threads have been done to death. But my front's are stuffed, due to exessive camber. I have 235/45/17 on my R33.

Just had a f/r camber/caster kit fitted and need new rubber.

Since its just for the fronts, I don't want to spend a ton of money.

Looking through the existing threads and calling around. This is what I got .

235

Nexxon $110

Kumho Ku31 $150

Nanking NS2 $150

Maxxis MAV1 $129

Dunlop SP3000A $175

Silverstone EX08 ??EV08 $140

Bridgestone Supercat $160

Toyo T1R $200

225

Sumitomo HTR $170

Diamondback $132

Ideally I would like to keep it under $150..

Are Maxxis Tyres any good??

I am so confused. Any suggestions welcome. Need something with good grip and not noisy

ALso I am not sure if should go with 225 or 235s

thanks

Link to comment
https://www.sau.com.au/forums/topic/219710-front-tyres-on-a-budget/
Share on other sites

If you are willing to go over $150 then the Toyo T1R's are a very good choice. The Silverstones are alright too for the money you pay. Some Maxxis tyres are good, but I dunno about that particular model you listed.

Also, I dunno what you're saying about them being only the fronts. Fronts are the ones taking most of the beating when you turn, so if you like taking corners at all I wouldnt skimp on those.

In general, you will find 235s to be cheaper than 225s, because they are a common size - not many cars take a 225.

I would suggest the B/S Supercats. The others may be cheaper, but they are "cheap". And you should not skimp on tyres - they are all that connect you and the car to the road.

I would go falken 452s like battery said, or the federal 595 if the falkens are too expensive. both are good performing tyres

after you installed the camber kits, did you get a wheel alignment? toe and camber both need to be OK to stop premature tyre wear

Thanks for the feedback guys. You are right the 235 are easier to get.

I realize the fronts are important, but you are correct, I should place more emphasis on them.

The Toyo's are a bit out of my price range. I noticed not much mention of the Dunlop sp3000A much on the forum. Are these any good. I am a dunlop fan from way back. Don't know about these ones though.

And Yes I did get a full wheel alignment done.

I go the Kumhos, I got them on that the moment and which cost about $230 each. I believe its a silica tyre, not to hard and not to soft in the perfomance range.

I had Nexens on before, nothing special, hard and is the cheap version of Bridgestone when I was told.

But before all that I had Yokohama E1's. Cost about $295 and preffer them for track use.

Nankang Ultrasport NSII. I've got em and they're great. Probably one of the best in a price/performance ratio.

As said 235/45 would be more common and cheaper/easier to get.

LOL!!! have u tried better tyres than those?

nankangs are prob one of the worst tyres ive ever used... no grip in the wet and just as poor in the dry.

if your gonna keep the car/wheels for awhile spend the money and get a decent set for the front... ive got yokohamas a-drive R1's cost me $250 a tyre in 235/40/18 so much grip!

go 2nd hand tyres

a good brand.

i usually pick up michellin's or pirelli's for about $80 a pop in those sizes with 70 or 80% tread on it.

IMO better than buying crap new tyres that dont wear and r like plastic matchbox wheels.

good tyres wear quickly.

I go the Kumhos, I got them on that the moment and which cost about $230 each. I believe its a silica tyre, not to hard and not to soft in the perfomance range.

I had Nexens on before, nothing special, hard and is the cheap version of Bridgestone when I was told.

But before all that I had Yokohama E1's. Cost about $295 and preffer them for track use.

I have the kumho's on my 300+rwkw 350z and i love them.

Its nice and grippy and i only get a little bit of wheel spin on 2nd gear when flooring it.

and the grip is great, esp for the price.

I have the kumho's on my 300+rwkw 350z and i love them.

Its nice and grippy and i only get a little bit of wheel spin on 2nd gear when flooring it.

and the grip is great, esp for the price.

Yeah Nice!

You got Twin turbos too? Right..? :geek:

Hi Guys,

I decidecd to go with the Kumho's. Don't seem so bad so far. A lot better than what I had. Thankyou for all your opinions/suggestions. Was very helpful.

thanks

Nice choice mate!

All the best.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
×
×
  • Create New...