Jump to content
SAU Community

Recommended Posts

So i've received a fine for under 15km/h which is 75 and 3 points. i think this was in a 50 Zone near anzac parade.

i've only just bought the car within the last 2 months. and it was on the written off regester, the previous buyer bought from auction and repaired it..

and its a diesel, so its surely no performance car at all.

now i've tested the car with a gps since the fine and my speedo is out. by a few km/h up high and a little more down low

would i have a leg to stand on in court representing myself? or would someone suggest a lawyer?

or should i just cop the fine even tho i thought i was doing the correct speed at the time.

the money from the fine isnt an issue, nor the points... i just want to keep my licence perfect :D

Edited by Angus Smart
Link to comment
https://www.sau.com.au/forums/topic/220535-contesting-a-speeding-fine/
Share on other sites

to tell the truth, i dont think its there problem if your speedo is out or not... I rekon you will get done even worse if you take it to court... I know it sucks and all but if it was me, id pay the fine, cop the points and fix the speedo... good luck to you if you take it on tho.

Anzac Pde is a 60 zone (mostly) untill you get to Alison road then it becomes a 70 zone all the way untill the end of Sydney Boys high. Obviously during school times the 70 becomes 40 zone.

The section you are talking about which has the camera is on Cleavland Street and not Anzac Pde, along the Sydney Girls side is where the camera is.

It's been there for months and months. Initially (as with all new cameras) there was a "warning issued" to speeders. But I guess that's expired.

The Cleavland street section is a 50 zone. Heck the whole of Cleavland street is 50km/hr.

Maybe you could try and say it's your first fine etc etc and get off it? Dunno

there is already a 10% speed allownace in place with nsw police i belive?

this allows people with speedo that are out with old cars get a way with an amount.

eg:

40kmph your allowed 44kmph

50 allowed 55

60 allowed 66

and so on .........

i dont think cops in nsw book you under the 10% differance, but Vic they do.

What was speed the cop put on the ticket?

What was speed the cop put on the ticket?

He got done by a fixed speed camera..

There are 3 signs before the camera and plenty of 50 zone signs at the sides, even on the ground it marks "50"

I love doing the speed limit there and seeing annoyed drivers tailgating me, coz they think that im going too slow, then over take me and speed up as they pass the camera. *FLASH* haw haw. :bunny:

Happened one night last week... Idiot car behind me was tail gating me.. I trott along slowly... She over takes me (Honda CRV Sport), just as it happen *FLASH* think I was in the flash too but I know I was doing 40km/hr so hopefully I wont get a fine. Otherwise id be pissed, and I have details of the other car anyways.

YOu can contest it, use the law mentioned above which allows a 10% tollerance eithaer way on your speedo, it takes awhile but it will have you with a clean slate.

for starters I'm not convinced that the allowance for speedo inaccuracy is law set at 10% and even it if is my maths tells me that 15km over 50km/h is 30% over 10kms would be 20% over. so unless he was only 5kms over that is not going to hold weight.

He didnt mention his speed, at least I didnt read it .. 15 and under is the lowest speeding fine you can get. I was just giving advice based on this law.. and yes its about 10% but Im not 100% sure.

This 15 and under is crap I think as it holds the same fine as someone doing 15 over the speed limit when he perhaps did 55kmph (which im pretty sure he could not have done as im pretty sure the fact is the the speed cameras flash at 57km/h 12% over road speed) I feel there should be a lower fine of 5k over and 1 demerit point.

In regards to the speedo it need to be calibrated on a dyno, from factory speedos come either to fast or more often than not to slow thats why the 10% leway exists. Oh and this is up to you to fix

Edited by DECIM8

I got done in a work truck, the speedo was out, i thought i was doin 95 but in actual fact i was doin 105. it was a 90 zone, work got the speedo check and found it was out , my boss rang the police or someone told them they changed the fine and loss of pionts but i still got done for 5 over.

  • 2 weeks later...

You're speedo, you're responsibility unfortunately. And with speeds, generally if it's done by us and not the camara we will put you give you the lower out of the 2, i.e. 15 and under rather than over, with all honesty you don't stand a chance in court. What people don't seem to understand is that a Magistrate can impose a higher fine than the IPB regulates if he feels it is a waste of the court's time, plus you will be issued court costs of $76 for the day, and Legal Representation if you had it.

Better to just pay up and be more cautious next time but its up to you at the end of the day =)

YOu can contest it, use the law mentioned above which allows a 10% tollerance eithaer way on your speedo, it takes awhile but it will have you with a clean slate.

There is a 10% speedo tolerance in the ADR's for vehicles manufactured after some date like 1976 but your information is incorrect. The speedometer can only 10% MORE than the actual speed of the vehicle. So if you are doing 60km, the speedo can read 66km, not vice versa.

Cleveland St has been a 50 zone for years and years. The cameras have been there since last November and there were big flashing messages boards there for 4 months.

No point going to court an saying you "Thought you were doing the right speed". You have to prove to a magistrate that either you WERE doing the speed limit or the camera was inaccurate. Good luck trying to prove either of them I'm afraid.

Idiot car behind me was tail gating me.. I trott along slowly... She over takes me (Honda CRV Sport)

Its not her fault VTAK kicked in while she was behind you. :yes:

And its a CRV Sport. If it wasn't meant to go fast, they wouldn't have called it a Sport.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...