Jump to content
SAU Community

Recommended Posts

As everyone else has already mentioned, 11's isn't too big an ask. 10's is quite a bit trickier!

If you want to be able to reel off consistant low 11's to high 10's (or better) then you may need to look at upgrading your gearset. I don't care what others may say on this subject but no matter how good the R box is it can blow 3rd gear if pushed hard. I've seen 3rd let go on quite a few R32 & R33 boxes.

If you only want to run 1 or 2 quick passes & then rest on your laurels you might get lucky with 3rd gear? A good friend of mine blew 3rd on his first run at Eastern Creek in his R33 (he knew about 3rd & took the shift easy too). His car has R34 N1 turbo's, cams & gears, Apexi PFC AVCR, head gasket & so on... 310kw @ all 4.

If I was in your position I'd buy an R that someone has already done all the hard work on. It'll save you a few $$$.

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Hi MELV, we have in the past .................

Had a standard R32 GTR (exhaust only) that did 11.9 on Bridgestone RE540's. Boost restrictor removed, so running 1 bar and with an OS Giken twin plate clutch. Total cost $29K.

Same car with 2530's, split dumps, Power FC, boost at 1.1 bar did an 11.2 on same tyres with same clutch. Total cost now up to $37K.

Tried 2540's but it was slower.

We then stuck an RB30 bottom end with RB25DE top end in it with a single Garrett GT3040BB and it did a high 10 on slicks. Total cost now $45K.

Based on our experiences, I think a standard R33 GTR with a good split dump and high flow cat exhaust, at 1.1 bar (standard turbos), twin plate OS Giken clutch and with a set of Nitto 555's on it, would do a high 11 pretty consistently. Cost around $40K.

The next half second off is gunno cost $10K, the next one $20K and one after $40K. That gets you to 9.9 and to go to low 9's, I reckon another $40K should just about do it.

40 + 10 + 20 + 40 + 40 = $150K, check with Munroe, he has personal experience, but I reckon that's about right.

Hope that added to the thread.

This thread has a few that are doing low 12's, and they're still running the stock turbos. Its a pity we don't have more GTR on that list...because there are plenty out there that will do 11's or 12's..

http://www.skylinesaustralia.com/forums/sh...&threadid=22444

It seems after that a good twin-turbo setup will get you into the 11's quite comfortably..

Then u gotta start thinking about a strong single turbo or big twin setup to get you into solid 10's.. its about then the engine starts to need some work. After that, pull out that chequebook, because you're gonna need it!

As Sydneykid says above prettymuch :)

Allright - a thread I can get my teeth into - get ready for essay.

First get what you want to end up with in your head.

Sydney Kid is right, there is an exponential curve upwards when it comes to 1/4 mile times. A std GTR is sensational value, then you want a bit more. Where do you want to stop - because with Drag Racing there is no end to it - ever.

If you want to pull nines - leave your GTR standard & do up an old school Drag car. Whats more important - having a house to live in & a decent standard of living or having a nine second GTR & living in a tent!!!

I bought a 13,000km GTR in April 2000, for $70,000! OK, they were dear back then. Since then i have spent over a quarter of a MILLON dollars on it. No shit. We were pioneering & wasted heaps on testing different combinations, but the fact remains that getting a GTR into the tens is expensive.

Nines is a whole nother level of badness - trust me - the amout of stuff we have broken would make the average guy cry.

The biggest problem is that when you get to tens it is just not enough.My car does not scare me at all. You get the bug - bad.

I have pulled 9.45 @ 153mph going sideways on every gearchange & got to the end thinking 2 things - pity i have to slow down now, & man I'd love to get a 9.3.

I had dinner with Mario recently & we discussed this exponential curve of climbing expense Vs diminishing value. I was not surprised at all that the amount he has spent on his 8 second GTR equals the value of my Race R33, Street R33, Hills R34, EVO 7, & my SS ute. In the same way my Race R33 = the value of a nice streetable 11 second R33 GTR & a decent house.

A lightly modified GTR that will easily pull 11's, handle hills driving with ease, & still be a pleasure to drive around town is definately the best value for money & time invested.

Of course we all have to learn from our own experiences, but if I had had someone explain to me how much it would actually cost to get serious times from a GTR 2 years ago, no-one on this forum would have any idea who I was 'cause i'd still have a Std GTR in the shed with a brand new 996 Porsche Turbo sitting beside it. You know why? Because i could actually use the thing for what i really like doing - driving really fast on the street & in the hills without getting defected.

There is no turning back now for me - I am commited to improving the R33 & now we are looking to get into the Jap top 10 on street tyres.With the current changes underway we should be there hopefully by Drag Combat this year.Will wait & see how it turns out.

Originally posted by Munro

I bought a 13,000km GTR in April 2000, for $70,000!     OK, they were dear back then. Since then i have spent over a quarter of a MILLON dollars on it.   No shit.

A lightly modified GTR that will easily pull 11's, handle hills driving with ease, & still be a pleasure to drive around town is definately the best value for money & time invested.

That was easily one of the most sobering pieces of text I've ever read on SAU or anywhere. In many ways, it reflects the problems that we all have here.

Do we highly modify a stock Skyline and get it running hard with everything done to it?

Or leave it relatively stock and just enjoy it for what it is?

I agree here. If I knew it was such a strong possibilty that I would blow turbos and engines on the Skyline BEFORE I bought it, I would get something else.

It's not even so much the money, it's the time, running around and the wait for things to be done.

T.

Yeah, i dont mean to put anyone off doing up their GTR. smart modifications are a great way to get the most out of your GTR - I'm just saying dont go to far.You will end up with a car that has cost you a house & you cant use it regulary anymore.

I love GTRs. They are fantastic value & one of the best performance cars available - all i'm saying is do your homework & be wise. If you seriously want to play - talk to the few guys that have already made all the mistakes & learn from our stuff ups.

Anyone that is serious about Drag Racing a GTR & has already started on the path of no return should talk to a reputed workshop like Tilbrooks or similar so the money can be spent on the right stuff from the beginning.

Trust me - you will save thousands of dollars & months of waiting.

From experience I can assure you that getting into the 11s takes minimal cost. A set of 2530s and the normal performance mods such as air filters, full exhaust , cam gears, fuel pump and injectors can get low-mid 11's easy.

To get to 10's I made the move to go a single turbo setup with a larger IC, cam shafts, valve springs, bigger injectors, new fuel system (twin pumps), forged pistons, stronger rods, Autronic, new gearset, triple plate clutch and the above mods. Also, a set of Nittos helps the cause big time!! I did however leave the stock GTR suspension in the car as my Tiens are too stiff and give no rear end squat thus taking traction away.

Just out of curiosity, Munro, what clutch are you in your R33 and how often do you replace it? I managed to get 14 runs and some normal street driving done (500kms) on my triple plate Ogura before it packed it in and began slipping. I'm just wondering whether this is the lifespan of clutches when I'm pushing 450+ rwkw a the strip.

Originally posted by Leewah

From experience I can assure you that getting into the 11s takes minimal cost.  A set of 2530s and the normal performance mods such as air filters, full exhaust , cam gears, fuel pump and injectors can get low-mid 11's easy.

To get to 10's I made the move to go a single turbo setup with a larger IC, cam shafts, valve springs, bigger injectors, new fuel system (twin pumps), forged pistons, stronger rods,  Autronic, new gearset, triple plate clutch and the above mods.  Also, a set of Nittos helps the cause big time!!  I did however leave the stock GTR suspension in the car as my Tiens are too stiff and give no rear end squat thus taking traction away.

Just out of curiosity, Munro, what clutch are you in your R33 and how often do you replace it?  I managed to get 14 runs and some normal street driving done (500kms) on my triple plate Ogura before it packed it in and began slipping.  I'm just wondering whether this is the lifespan of clutches when I'm pushing 450+ rwkw a the strip.

Oooooops. Clicked quote rather than edit. Mods, please remove this post.

My Race R33 has a quad plate OS clutch with an 8 bolt flywheel to suit the OS crank.After 30-40 passes it is still in great condition - but I only use it on the start line.With the Holinger i dont need the clutch on gearchanges & just pull it through with a blip off the throttle to relieve torque from the gear faces.

I think it's the street driving & riding the clutch off the lights to get a smooth take off at slow speeds that wears them out.

I agree with you - 11's aren't that hard, but when you start making all that extra power with bolt ons the std internal engine will only last so long, then the gearbox will go, then you need better clutch, then you start snapping driveshafts, then you end up putting all the killer driveline stuff in & think - hey, i need more power now & off you go again.

Also, in most states, once you run 10's they require cages/harness/fire suits etc.

R33GTR,

NISMO COMPUTER

NISMO N1 TURBO

NISMO LSD

NISMO GMAX TWIN PLATE CLUTCH

NISMO BODY KITS

NISMO SPEEDO

HKS BOOST CONTROLL

HKS COILOVER SUSPENSION

18 INCH SSR 5 SPOKE WHEEL WITH 265/35/18 TYRES,

CAR WILL MAKE AROUND 550HP AT ENGINE,

$57000

does that sound like a good package ? i wish it had cam gears with it.

also whats a NISMO n1 turbo ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nice, thanks for sharing your progress....that's a pretty long list you are putting into it!
    • Decided to upgrade my pressurised plastic coolant expansion tank for a fancy pants alloy version The OEM versions can get brittle, even the new plastic one I got when I first got the car is a starting to show signs of "stress" I wasn't cheap, but it is basically unbreakable
    • Morning all, I have an RB25DET Neo that's in need of a rebuild. Will need new pistons etc due to detonation damage. Would anyone be able to recommend a shop in Southeast Queensland who I could bring my long motor to for a rebuild? Just want someone who knows RBs and whos built a bunch of them before. TLDR - recommended engine shops for RB rebuild.
    • Gday Thought it was about time I started a build thread! As expected this project has snowballed into a huge financial liability, but unless you’re strong willed and responsible, it’s not a surprise. Background -  My first turbo car was an R32 GTS-4, got my full license and then totalled my Au Falcon a week later, so while trying to sell my RMZ450 dirtbike to buy another car a bloke offered to swap the R32 which at the time I felt like I was ripped off but looking back and seeing prices of those now ($40kish) it was a good deal, I didn’t know enough about these cars to appreciate what I had so sold it before the RB20 blew up. Between here and there, out of 12 cars I’ve owned the note worthy ones are a V8 Lexus SC400 (soarer), a couple of XR6 Turbos and my beloved S15 which I had for about 3 years, picked it up for $12500, repairable write off but she was fine, gun metal grey/pewter and bone stock/unmolested until I got my hands on it. Ended up spending about the value of the car and 280kw, 2 demerit points by the time I got defected and sold it for $14500 (also $40kish in today’s market, rip) Fast forward to the present day, I’m in a much better position financially and daily an MQ Triton (great cars, pipe down Ranger Bois), I cruised marketplace and car sales for a few months looking for another R32, the best deal I could find was an absolute rust bucket half finished project for $12000, until this R33 popped up in Port Macquarie for $18k - unregistered and barely running but decent shape, kept an eye on it for a few weeks and the price steadily dropped, $16k then $15k then $14k, that was the point where I was like shit someone’s gonna snatch this up! It was owned by a young bloke who had big plans but him and his missus just had a baby so smartest move financially for them but big gain for me. So 2 days later I’m towing a car trailer to pick this thing up. Roughly 2 weeks and $3500 later I’m cruising around Newcastle in my beat up R33 all smiles and dose noises! It only needed some basic shit to get it going, coil packs and air flow meter, electrical stuff and all fluids changed, 158k kms and running pretty good, nice smooth engine after oil and coolant flush - when I say coolant I mean it had been filled up with tap water, every gallery and heater element was filled with rust, 8-9 flushes later and still had brown liquid coming out but she’ll be right. The car was painted R34 Bayside Blue at some point but whether it was a cheap job or just not looked after is anyone’s guess, clear coat flaking like sausage roll.  Was rethinking my choices and contemplating life, had it up for sale for $22k - still cheaper than any registered R33 but got little interest, next minute I had an opportunity at work - 6 months overseas for good money, so that was a no brainer, fast forward again and here we are with a 50% finished project. Current Mods - 200ish KW according to butt dyno Was tuned with Apexi PowerFC EBC (old school Greddy Profec)  Stock turbo (more shaft play than a Tinder date gone right) 3inch turbo back Varex muffler  Aftermarket injectors of mystery size, Power FC showed 36% duty cycle at full boost so not behd good size Someone had good intentions but stuck with the stock R33 MAF so we had misfires at 6000rpm due to the MAF hitting 5.2V So far I’ve redone the entire interior with carpet form Car Mats Direct, new Seats and steering wheel from Autotechnica, also sound system by Autobarn (mainly Kicker) Also MCA pro comfort coil overs - Hands down best purchase yet, worlds of improvement over the tired 30yrold shocks Goals - 450kw/600hp on flex tune New paint job - Midnight Purple 2 Engine is at the shop getting rebuilt with forged rods a pistons, new valves and springs, ATI Harmonic balancer, Aeroflow 7.5L sump, rear head drain and oil restrictors as per oil control thread* and cam covers modded for larger breathers, other stuff I can’t recall of the top of my head Parts purchased and to be installed once the engine is done -  Engine loom from Wiring Specialties including these options: Haltech Nexus S3 R35 Coil pack conversion  PRP Dual Trigger kit Fan controller  Other Parts -  262 Kelford Cams Turbo - Hypergear ATR43SS3-ProS with T51R mod (whistly boi) 6 boost manifold (high mount) 50mm Turbosmart Pro gate (plumbed back for legal reasons) HKS Super Turbo Exhaust with High Flow Cat Custom 3.5inch dump and front pipe 1500cc Bosch injectors  Fuel Pump walbro 525 Haltech MAP and IAT sensors Haltech Flex Sensor Fenix Radiator with dual thermo fans LS1 Alternator Kit Oil Filter Relocation from EFI solutions and Cooling pro oil cooler Many other things sitting in my garage waiting for that engine to come back. Progress pics to follow -  
    • Losses have to be less with DC coupling. Provided the battery inverter has decent MPP tracking ability - which really shouldn't be a problem. It's not 2005 any more.
×
×
  • Create New...