Jump to content
SAU Community

Places For Afterparty

r_o_b

By r_o_b,
in Victoria

 Share

Recommended Posts

adam-__- Grand Master

adam-__-

Posted
Posted (edited)

:laughing-smiley-014:

I think I saw him on the train the other day, I think it was on Friday. No shades on though.

Edit: What's this for if you don't mind me asking? I'm sure it would help others choose a location for you as well. If it's a birthday party, choose a house somewhere, wedding, go to some restaurant, etc.

Edited by adam-__-
r_o_b Apprentice

r_o_b

Posted
  • Author
Posted
:laughing-smiley-014:

I think I saw him on the train the other day, I think it was on Friday. No shades on though.

Edit: What's this for if you don't mind me asking? I'm sure it would help others choose a location for you as well. If it's a birthday party, choose a house somewhere, wedding, go to some restaurant, etc.

Its for an afterparty, for a yr12 formal.

gdogzgtr Proficient

gdogzgtr

Posted
Posted

I would be highly surprised if any club/pub will allow it with the Liquor Licensing laws. Best bet would be with a local scout hall or similiar and just arrange security, DJ etc.

Where I work there used to be lots held at a Dance Studio but in the end I was the main one responsible for shutting them down permanently. Not the invited guests fault but about 100-200 local youths that cause trouble tried to gatecrash everyone of them so I put an end to it as I ended up being tied up there the whole time of the party every time.

Even shut one down with 400 people and seized all alcohol at party which was left with security making them very happy as there was about 5 bins full.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...