Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

also, I'm not sure what type of tyres you have, but if they are cheapies then for sure they would have contributed to this incident. having good tyres is so important. they are the only link to the road and there is no point having great suspension, or good brakes or good power if you then slap on some nexen/nangkang/wanli tyres on it. yes good tyres are crazy expensive but the safety of you and your family and other people on the road make them well worthwhile.

Thanks DIF and Cassbo..

Actually talked about this later that night.. one of these days my partner is gonna take me out for a bit of defensive driving .. he did a course a while back..

I wish I had known to just take my foot off the accelerator but unfortunately it all comes down to my inexperience as a driver.. I think we may be getting a shitter just for me to drive around to gain more experience before I drive the Skyline again.. you know when I look back I think I pushed harder on the accelerator as I lost control because I did a full 180.. I've learnt that lesson the hard way..

Hiya Beer Baron I'm not sure about the tyres.. but I suspected that my wheel alignment was a little off before the incident.. silly me thought I could leave it for a little while because it didn't seem that bad.. just goes to show hey..

I can't even tell what tyres you have on there.. But if you are on a budget I would highly recommend a set of Federals SS595 they are in the cheaper bracket very affordable and they are great tyres.. Too soft for the track but perfect street tyres if you are on a budget or have a family.

I've had this set on my car for over a year now and have done a few trackdays and driver training/ skidpans on them and they have held up very well.

I can't even tell what tyres you have on there.. But if you are on a budget I would highly recommend a set of Federals SS595 they are in the cheaper bracket very affordable and they are great tyres.. Too soft for the track but perfect street tyres if you are on a budget or have a family.

Do they sell them at any tyre shop? Like bob jane? How much were they roughly?

Thanks heaps DIF.. because we are on a very tight budget.. still need to do 100k service on both our cars.. now coz I've stuffed the tyre and alignment and whatnot that's another few hundred.. not to mention new rims..

100k can be expensive depending on what you need can sometimes cost up to $600 +

I have 34GTX rims on my car at the moment which are 225-35-16 (I think) and I paid around $147 a tyre.

The only places that do sell Feds are Payless tyres and ABC tyres I'm not sure if anyone else does but my advice will be to shop around for the right price. They might have the dealers on their website if you have a look..

lol..

OK well it turns out to be the lower suspension sub frame.. trying to source out parts.. anyone know of any other places to get parts.. hopefully in the hills shire.. blacktown area? even parramatta.. ..

hey Cassbo.. where is SSS located.. do u happen to have their phone number? I've looked it up and there are quiet a few companies called SSS.. there's SSS automotive imports.. SSS and mechanical .. SSS auto parts.. which one? :teehee:

Cheers ;)

talk to mark at hills motorsport, at the back of the complex at 2a victoria ave castle hill. he will have all the stuff you need in stock.

but it wont be the whole sub frame, just lower control arm and/or tie rod

hey Cassbo.. where is SSS located.. do u happen to have their phone number? I've looked it up and there are quiet a few companies called SSS.. there's SSS automotive imports.. SSS and mechanical .. SSS auto parts.. which one? :teehee:

Cheers :)

SSS Automotive

(02) 9896 6111 or (02) 9636 4301

Unit 6, 120 Gilba Road, Girraween

I suggest taking in the bent parts for identification purposes. I had to go there twice because I picked up a driver's side lower control arm instead of a passenger side one. Wasn't a massive problem, just an easy swap, but it did involve driving there and back twice.

Be careful there though, there are plenty of shiny things in there that will tempt you to spend more than you need to ;)

Cassbo,is that damage to your smic or just a warp in the photograph?

it is indeed real.... although if I hadn't of seen it in real life I would of sworn he did some magic with the photo :)

Pm replied also Anna... :P

hey Jeffworld2.. not yet.. need to find a subframe for the 34.. I'm sure that's what my uncle was talking about (he had a look at it lastnight).. because he said it wasn't the control arms.. just the lower suspension frame so I'm assuming it's the whole frame.. for the rear suspension..?

dad's gonna call me back.. it's actually at my parents house in Glenwood (hills area).. while I'm here in Mount Annan without my poor baby.. wonder how she's holding..

Thanks a heap for all the help.. thanks Duncan, anna, matt, jeff, george... we'll call around.. i'll just confirm with my uncle as to which part it is we need.. then we can get the ball rolling...

WILL KEEP YOU UPDATED!

cheers :thumbsup:

AH, it's been pissing down here, so we've been seeing a heap of people in the same predicament :) Not cool for you, I hope you can get it all fixed up no hassels :)

Defensive driver training is invaluable, and skidpan is actually so much fun that everytime it rains, you're gonna deliberately want to kick it out :( I kid you not! If you're trainers in Syd are anything like ours here, you'll get your ass kicked if you just 'take your foot off the accelerator'. The point of defensive driving is to learn how avoid as much damage with as little effort as possible, in the case of a slide, continuing with it, but steering through it safely, to miss obstacles & get yourself straight again. If you take your foot off, all you'll do is regain grip, and you don't want that while you're steering!! :thumbsup: Anyway they're a tonne of fun, you'll thoroughly enjoy yourself.

Not sure about where you guys get your federals down there, but all the Jax Quickfit stores here have a deal with the Qld supplier, you might find they have the same deal there :) Anyway it's worth trying!

Let's hope it's just the alignment :D

Anna.

hello again.. you guys were right.. it was actually the lower right suspension arm that was bent.. dad went down to sss in Girraween to pick up the part today... hopefully it's the right one..

Uncle is fixing it on thursday hopefully.. and she'll be back on the rd by the weekend *fingers crossed*...

HOLY POO ANOTHER ANNA!!!.. Anna's must love Skylines.. :) I know I do..

Yerr will stick to partner teaching me for the mean time.. then when I get the confidence I might check it out.. but atm I don't think we can afford to do any damage to our cars.. we have three young kiddies.. anyone wanna buy any of them.. they're good kids.. not very picky.. our oldest loves fast cars and Skylines.. and they help out around the house.. goodlooking kids too.. any takers??? :D

Be careful there though, there are plenty of shiny things in there that will tempt you to spend more than you need to :D

AHAHAHAHA .. me dad went cause it's only 15mins from where they live.. temptation avoided.. :)

Good luck with the repairs,

Let me know if you need any genuine parts new from Japan, all I need is you to Pm me your car's Japanese VIN and the parts you need,

I work at a car dealership with Nissan parts department and I can get a discount.

I was recently up for some new rotors, castor rods and front control arms for my r34 as my current ones were worn and the difference in price to retail was pretty substantial.

Hope it works out!

Suspension is all fixed :D ... getting 4 new rims and tyres fitted today.. turns out both rims at the rear were damaged .. the rear left was damaged on the inside...

Can't wait.. getting the car back tomorrow :)..

Thanks for all the help guys.. I'm so glad there are lots of people here willing to lend out a helping hand!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...