Jump to content
SAU Community

Gearbox Re-conditioners ?

Shadex

By Shadex,
in South Australia

 Share

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

chef_stagea Grand Master

chef_stagea

Posted
Posted

+1 for mv... another auto shop had my stag for close to 3 and a half weeks.. couldnt sus the problem properly.. mike had it back to me with in 3 days of it being droped off.. and i even took it to him way b4 i was ment to :) 100% champ... was a little unsure taking it there to begin with.. but he will give u an on the spot $ figure and tell/show you what you got worked on in detail..

Dohmar Grand Master

Dohmar

Posted
Posted
I rang MV not long ago and they told me they only do automatic transmissions.

Hence MV Automatics lol

Same, I called them today and they recommended I call "Precision Differentials and Gearbox" on Port Road...

Will call them later, interested to know if they can do it for under a grand... probably not tho..

How hard is it to pull a gbox apart and replace the bits? I don't care if it takes a long time, but if it needs special equipment/experience then I'd have to give it a miss..

-D

jrm Veteran

jrm

Posted
Posted
Same, I called them today and they recommended I call "Precision Differentials and Gearbox" on Port Road...

Will call them later, interested to know if they can do it for under a grand... probably not tho..

How hard is it to pull a gbox apart and replace the bits? I don't care if it takes a long time, but if it needs special equipment/experience then I'd have to give it a miss..

-D

I dealt with a Peter Wienert over at Precision Differentials and Gearbox Centre, when I had issues with my N14 SSS; He took my car for a spin around the block, and he said it didn't seem quite right. I had my mechanic rip out and send over the 'box to rip open and have a looksee inside and figure out if it was cheaper to fix or replace.

Turned out that it was too busted to fix, and I ended up picking up another box - but - these guys did the open up and check out for free for me, which I was blown away by. They seemed totally professional to me. :D

Jenna

Dohmar Grand Master

Dohmar

Posted
Posted
Give Rowell & Searle in Pulteney St a call.

They took a look at my gearbox when it shat itself, offered to rebuild it but suggested I look at the cost of a replacement, being RB20 gear it was cheaper to go that way.

I've been to rowell and searle before when I needed work done on my 31's auto. IIRC they don't do manuals? Can someone confirm this? Either way, I was very happy with the work done. They did a good job

-D

Shadex Collaborator

Shadex

Posted
  • Author
Posted

Im terms of a bigger and better gearbox i rang up Horsepowerinabox today, and PPGearbox's do a 1st to 4th set up for around 5700.. And thats just the shafts etc... Thats the cheapest one they have but its guaranteed to be 500% better/stronger then the original box. But thats not including labour to build it and put it all back together.. So im rather confused on what to do now lol. Use my standard box rebuild it and if i do put more power in to it risk having it go again, Or go to the point were im spending 7 grand or so on a box lol.

Dohmar Grand Master

Dohmar

Posted
Posted
Im terms of a bigger and better gearbox i rang up Horsepowerinabox today, and PPGearbox's do a 1st to 4th set up for around 5700.. And thats just the shafts etc... Thats the cheapest one they have but its guaranteed to be 500% better/stronger then the original box. But thats not including labour to build it and put it all back together.. So im rather confused on what to do now lol. Use my standard box rebuild it and if i do put more power in to it risk having it go again, Or go to the point were im spending 7 grand or so on a box lol.

Your best bet (imho) for anything serious is for you to buy a shagged box which already requires a rebuild and buy the OS Giken 5 speed kit. And get someone reputable to do it (Rowell & Searle, Precision Gearbox & Diff). Labour is never going to be cheap, and if you're rebuilding with good stuff, it'll definately cost you... that said, in 4-5 weeks I'll be removing my current box to fit a replacement, so if you wanna grab a box needing a rebuild, send me a message

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      r34's love to squeal

      By MBS206 · Posted

      And make sure the belts are tightened appropriately too.
    • MBS206
      Rb26 iron block limit

      By MBS206 · Posted

      They care about emissions, and cost the most. Save weight where possible, and make manufacturing easier. Less material also let's the engine transfer heat to water quicker, and bring the engine up to temp quicker, better for emissions and getting them past their warranty period.
    • joshuaho96
      Rb26 iron block limit

      By joshuaho96 · Posted

      I was under the impression the reason why OEMs are going with solutions like relatively thin "right-sized" cylinder walls with technologies like PTWA and open deck is because they care a lot about whatever marginal knock margin benefits they get from that vs the structural rigidity benefits of a closed deck block and thicker cylinder walls. I also see some weird stuff like plastic inserts in the water jacket around the cylinders to try and equalize cylinder wall temperatures. re: the PRP blocks and heads at the end of the day it's hard to know what is and isn't going to work there, just have to see what the initial buyers say about it.
    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • joshuaho96
      Rb26 iron block limit

      By joshuaho96 · Posted

      https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
×
×
  • Create New...