Jump to content
SAU Community

Recommended Posts

best way wuld be to fiddle around in the lok where u broke it done dat on one of mmy mates old car just fiddle with a screw driver to move the latch or if u can be bothered remove rear seats and somehow dis conect the lok if u can reach lol but prob be easier to do it from the outside to fiddle with the lok. let me no how it goes.

Link to comment
https://www.sau.com.au/forums/topic/223599-r31-boot/#findComment-3939414
Share on other sites

u took the lock out and didnt put it back in? so theres still a hole in there? if so there should be a rod/lever of some sort the attaches to the back of the lock, just pull it in every direction and the boot should pop open? if not, rip the back seats out (or fold em down if you can)

Link to comment
https://www.sau.com.au/forums/topic/223599-r31-boot/#findComment-3942106
Share on other sites

Try the back seats, I can't recall if you can remove them and get access to the boot without unbolting them from behind (its been ages since I've touched them).

There is a bar running inside the boot to release it but I'm unsure if you can get to it.

Have you tried the R31 Skyline Club?

Link to comment
https://www.sau.com.au/forums/topic/223599-r31-boot/#findComment-3943132
Share on other sites

You obviously dont have the fold down rear seat otherwise you would have crawled through there?

Remove the back seat or find the rod through the hole.

Is the manual release lever not working coz theres no tension? It might have popped off or previous owner disconnected it to make acessing the boot harder for theives?

Try yanking the release cable with some pliers. If its been disconnected/failed at the boot end then its one of the first two options.

Link to comment
https://www.sau.com.au/forums/topic/223599-r31-boot/#findComment-3943613
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...