Jump to content
SAU Community

Recommended Posts

Time for some updates...

Yesterday, I managed to strip out my R32...

I removed the engine and transmission, Doors, trunk hood, rear lights and a lot of boxes that I do not know what was, and probably will never use.

I also manage to remove the back axle cradle with everything on, so the car is practically completely stripped out...

Today I will try and get everything removed from the cradle and I will deliver the shell and the cradle to sandblasting to remove all the rust, and primed, so it will not rust again.

Then when I receive it again, I can start on the Firewall and gearbox tunnel.

I will also try changing from the ball thing used on the spindle for the HICAS to a bushing like the one on S13/S14. If the S13/S14 does not fit, I will make something similar...

Here are some pictures, sorry for the large size:

web.jpgweb.jpgweb.jpg

web.jpgweb.jpgweb.jpg

web.jpgweb.jpgweb.jpg

web.jpgweb.jpg

  • 3 weeks later...
  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

More updates...

My sandblaster dude had taken a vacation, so I did not send the car off to be sandblasted.

Instead I manually removed the sound isolation on the floor.

I also started on the firewall, and hopefully I will be finished with it at the end of this week.

I also got my new air filter kit from K&N Air filter. The kit is for 2007 Corvette LS7, and it is HUGE! and my new brakes are on the way from Performance Guru, James. D2 356 8Pot front brake Kit, 330, 6pot rear Brake Kit.

So parts are poring inn, and car is being worked on.

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

  • 2 weeks later...

Hi!

Time for build update!

In the last week I have managed to make a firewall, and im damed proud of it! It is looking nice, and is stiff.

I made a firewall out of a plain sheet metal, after I reinstalled the engine:

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

Don't be scared of the small gap between the firewall and transmission, I was needed to go offshore on short notice, so I did not finished cutting it out. If you see the black line, thats where I will cut it when Im back onshore again... Leaving plenty of space to remove transmission with out removing the engine.

And the brakes that I ordered the 1. December arrived at my fathers shop the 5. December. and they where huge.

Sorry that I do not have any pictures of them yet.

Im also struggling with a clutch Master Cylinder and clutch.

Options on master Cylinders:

I can only use Wilwood master Cylinders, since I have a Wilwood pedal Box:

Bore: 0.625in, Stroke: 1.300in, Volume: 6.54ml

Bore: 0.750in, Stroke: 1.100in, Volume: 7.96ml

Bore: 0.875in, Stroke: 1.200in, Volume: 11.82ml

And clutch alternatives:

Fidanza Twin Disc Clutch Kits

McLeod RST Street Twin Clutch Kits

Single Plate clutch (Suggestions?)

Origional Corvette LS3 (Followed the engine when I bought it)

Please come with suggestions...

Edited by Morten Kiil Finsaas
  • 2 weeks later...

Finaly got some work done. Almost done with the gearbox tunnel.

The framework of the tunnel is made by 20x20x1.5mm square steel, so I can "Hang" the gearbox from it.

It has taken some hours making it, but I think its going to be great.

Here are the pictures:

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

is that solid bar?

:P

Its welded to the old tunnel, and to the new firewall if thats what you mean. Since its also holding the gearbox, It needs to be strong.

the steel is a square bar, 20mmx20mm of 1.5mm thick steel, not a solid bar.

  • 2 weeks later...

Have got some work done.

The firewall is finished, and gearbox tunnel is finish. And so are the floor is also finished..

I also managed to install the S14 left hand steering and steering column, and it fits great! So the next step is to mount the pedals and everything under the car, so I can get the wheels on. Then I need to remove all the roll-cage bars, so my roll-cage builder can build a new WRC style one in the middle of january.

Here are pictures from the gearbox tunnel. The four pannels that is not mounted on the last picture, will be bolted for easy access to the bolts and connectors and so on:

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

Here are pictures from the mounting of the stearing:

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

I also recieved a use carbon wing, in pritty good shape, for sheep amunt of money:

web.jpg

web.jpg

Here are pictures of the new front brakes that I recieved early december. The rear brakes are identical, but a little bit smaller. (Front: 356mm, 8pot. rear: 330mm, 6pot.):

web.jpg

web.jpg

web.jpg

web.jpg

I have managed to get some work done on newyears eve...

I managed to get the brake pedal assembly mounted, and Im happy with the mounting. I used a friend of mines Master brake cilynders, to check for clearance.

Next step is to remove the rollcage and make it ready for the new rollcage. Also I need to install all the old parts for the wheels so I can roll and stear the car when it is at the rollcage builder...

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

Recently I managed to mount the front suspencion on the car, and the front brakes. But the 18" wheels that I have needs spacers to be mounted...

web.jpg

I also managed to mount the whole back wheel suspesion also, but Im missing some small things...

The rollcage is removed, only grinding on the old welds and replacing small parts of sheet metal left, and it is ready for rollcage mounting.

So this project is on hold util I get back from work in about two wheeks, and the new parts arrives...

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

web.jpg

same brakes Stu has on his 32 I think also a few other guys here are using them.

looks good :D

Yea I know he has these brakes...

They are supposed to be good brakes for less money...

They are about 1/10th of new simular Brembo brakes (I checked... :) ), but I do not think they are only 1/10th of the quality eather...

And, I just passed 200 images in my gallery for the build... :Pgallery.mac.com/mortenkf

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...