Jump to content
SAU Community

Recommended Posts

1x large permapine post, 1x guard rail and various little white reflective posts. I've had it for no more than a month :kiss:

LOL sounds like your enjoying it. Still feel all alien to be sliding or getting back into the swing of things now?

Man, I want a slider.... Someone buy my GT-R :D. Would have been good to see some before shots of the damage lol

Edited by Weezy
learn how to drive will ya :)

Nah.

Deej.

LOL sounds like your enjoying it. Still feel all alien to be sliding or getting back into the swing of things now?

Man, I want a slider.... Someone buy my GT-R :) . Would have been good to see some before shots of the damage lol

Surprisingly had no trouble getting back into the groove. After 7 months I was expecting to be super shit but hit up a few corners in the dry and it all came flooding back. Throw in some rain and its linking corners in 3rd :blink:

This is how it looked before I really got into skidding it

post-50221-1275553558_thumb.jpg

Edited by AndrewJZX100

Yep love the GT-Cs on your GTR!!! I nearly bought some for the 35 from JIS, but they had about +10 less offset then I wanted :blink: (and really were more than I wanted to spend for a daily)

post-669-1275560681_thumb.jpg

but got these instead :)

post-669-1275561069_thumb.jpg

18 x 10 +24 on the rear - won't fit under your guards mate - not even close :blink: Perfect for my car though. Shame the fronts are 9 x 24 - not even close to tuff enough for my car. In fact my 9.5 +20s are only just ok for the front, but leave the rears on my car lacking. I am going to put 20mm bolt-on spacers on the 35 for the Kadina show - so they will be 9.5 +0 on the rear :)

18 x 10 +24 on the rear - won't fit under your guards mate - not even close :thumbsup: Perfect for my car though. Shame the fronts are 9 x 24 - not even close to tuff enough for my car. In fact my 9.5 +20s are only just ok for the front, but leave the rears on my car lacking. I am going to put 20mm bolt-on spacers on the 35 for the Kadina show - so they will be 9.5 +0 on the rear :nyaanyaa:

I was looking to get 18 x 9 at the front with a + 18.......and 18 x 10 at the rears + 22

so only a trail fit away now :)

I was looking to get 18 x 9 at the front with a + 18.......and 18 x 10 at the rears + 22

so only a trail fit away now :)

should be fun.

this an 18 x 10 +12 on the 14.

IMG_3180.jpg

IMG_3181-1.jpg

IMG_3182.jpg

Edited by scandyflick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...